Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0321096 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41221 2.REMOVE FRONT DIFFERENTIAL RING GEAR

a.
C317727C01
1.167,1.469 0.427,0.99 0.427,0.99 1.229,1.406 true 0.24,0.833 0.677,1.25 0.438,0.417 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front differential case.


b.
C317728

Remove the 12 bolts from the front differential ring gear.


c.
C317729

Using a plastic hammer, tap on the front differential ring gear to remove it from the front differential case.


Hide 41342A 3.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C317730

Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case.


Hide 41342F 4.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C317731

Remove the front No. 1 differential pinion shaft from the front differential case.


Hide 5.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 6.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Install SST as shown in the illustration and tighten it.

C317732C01
4.625,0.26 5.146,0.26 false 5.104,1.667 4.885,1.521 4.885,1.521 5.094,1.396 false 4.375,1.521 4.896,1.521 false 3.177,0.229 3.51,0.542 0.333,0.313 10 false *a 1.042,2.406 1.417,2.677 0.375,0.271 10 false *b 4.313,0.177 4.802,0.615 0.49,0.438 10 false SST 4.063,1.448 4.552,1.885 0.49,0.438 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to remove the front differential pinions.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C317733C01
2.76,2.833 2.573,2.833 2.573,2.833 2.573,2.365 false 1.594,0.781 1.917,1.042 0.323,0.26 10 false *a 2.823,2.76 3.208,3.063 0.385,0.302 10 false SST
*a Turn


Install SST as shown in the illustration and rotate the front differential side gear to remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinions and front differential pinion thrust washers.



c.
C317734C01
2.198,0.177 2.406,0.177 false 2.281,0.333 2.448,0.333 false 2.188,0.719 2.354,0.719 false 2.188,1.323 2.354,1.323 false 2.292,1.719 2.458,1.719 false 2.198,1.854 2.417,1.854 false 2.021,0.635 2.333,0.792 0.313,0.156 10 false *1 2.125,0.25 2.438,0.406 0.313,0.156 10 false *2 2.042,0.104 2.354,0.26 0.313,0.156 10 false *3 2.042,1.24 2.354,1.396 0.313,0.156 10 false *1 2.146,1.625 2.458,1.781 0.313,0.156 10 false *2 2.042,1.771 2.354,1.927 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front differential case.

NOTICE:

Do not drop the front differential side gears, front No. 1 differential side gear thrust washers or conical springs.