Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321405 FRONT CRANKSHAFT OIL SEAL A

2AR-FE ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL TIMING CHAIN COVER OIL SEAL

a.

w/o Side Lip:

i.

Apply MP grease to the lip of a new timing gear case or timing chain case oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




ii.
A452465C02
0.813,0.292 1.5,0.292 1.5,0.292 1.688,0.521 true 2.094,1.479 2.406,1.677 0.313,0.198 10 false *a 0.5,0.208 0.958,0.406 0.458,0.198 10 false SST 2.156,3.802 2.469,4 0.313,0.198 10 false *b 2.344,4.188 2.656,4.385 0.313,0.198 10 false *c
*a -0.75 to -1.45 mm (-0.0295 to -0.0571 in.)
*b Dust Seal
*c Lip


Using SST and a plastic-faced hammer, tap in the timing gear case or timing chain case oil seal.

SST
09710-20011  (09710-06071)

Standard depth:

-0.75 to -1.45 mm (-0.0295 to -0.0571 in.) (From the edge of the timing chain cover sub-assembly)


NOTICE:
·

Do not tap in the timing gear case or timing chain case oil seal at an angle.

·

Wipe off any MP grease from the crankshaft.





b.

w/ Side Lip:

i.

Apply MP grease to the lip of a new timing gear case or timing chain case oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.

·

Do not allow MP grease to contact the side lip.




ii.
A452467C02
0.885,0.625 0.677,0.292 0.677,0.292 0.417,0.292 false 2.198,0.76 1.99,0.427 1.99,0.427 1.729,0.427 false 1,3.219 0.917,2.885 0.917,2.885 0.719,2.885 false 1.052,3.396 0.958,3.792 0.958,3.792 0.76,3.792 false 2.188,3.208 2.104,2.875 2.104,2.875 1.906,2.875 false 2.333,3.417 2.24,3.813 2.24,3.813 2.042,3.813 false 0.115,0.208 0.573,0.406 0.458,0.198 10 false SST 1.521,0.333 1.979,0.531 0.458,0.198 10 false *a 1.031,4.063 1.49,4.26 0.458,0.198 10 false *b 2.292,4.063 2.75,4.26 0.458,0.198 10 false *c 0.417,2.792 0.875,2.99 0.458,0.198 10 false SST 0.531,3.708 0.99,3.906 0.458,0.198 10 false *a 1.573,2.792 2.031,2.99 0.458,0.198 10 false SST 1.823,3.719 2.281,3.917 0.458,0.198 10 false *a
*a Side Lip
*b Correct
*c Incorrect


Fit the timing gear case or timing chain case oil seal to SST.

SST
09710-20011  (09710-06071)

NOTICE:

Visually check that the side lip is not caught on SST.



iii.
A452466C02
0.802,0.292 1.49,0.292 1.49,0.292 1.677,0.521 true 1.458,2.021 1.865,2.021 1.865,2.021 2.146,2.354 true 2.104,1.469 2.417,1.667 0.313,0.198 10 false *a 0.5,0.198 0.958,0.396 0.458,0.198 10 false SST 1.25,1.927 1.563,2.125 0.313,0.198 10 false *b 2.146,3.792 2.458,3.99 0.313,0.198 10 false *c 2.333,4.188 2.646,4.385 0.313,0.198 10 false *d
*a -0.75 to -1.45 mm (-0.0295 to -0.0571 in.)
*b Side Lip
*c Dust Seal
*d Lip


Using SST and a plastic-faced hammer, tap in the timing gear case or timing chain case oil seal.

Standard depth:

-0.75 to -1.45 mm (-0.0295 to -0.0571 in.) (From the edge of the timing chain cover sub-assembly)


NOTICE:
·

Do not tap in the timing gear case or timing chain case oil seal at an angle.

·

Wipe off any MP grease from the crankshaft.





Hide 13471 2.INSTALL CRANKSHAFT PULLEY

a.

Align the crankshaft timing gear key with the key groove of the crankshaft pulley.


b.
A413602C01
1.646,0.885 2.615,1.156 2.615,1.156 1.781,0.417 true 2.281,0.24 2.51,0.438 0.229,0.198 10 true *a 1.146,1.74 1.375,1.938 0.229,0.198 10 true *b 2.667,1.094 3.063,1.302 0.396,0.208 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley and install the crankshaft pulley bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)

HINT:

Insert a few washers (total thickness: approximately 5.0 mm (0.197 in.)) between SST (09213-70011) and SST (09214-00030).



Hide 16361A 3.INSTALL V-RIBBED BELT

Hide 4.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE