Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321409 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A194970N09
0.958,0.656 0.469,0.448 0.469,0.448 1.083,1.104 true 0.104,0.365 0.396,0.531 0.292,0.167 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194985

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


Standard Bush Length:

41.3 to 41.7 mm (1.63 to 1.64 in.)


If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.
A194972C08
0.99,0.813 0.271,0.333 0.271,0.333 1.219,1.323 true 2.448,0.542 2.646,0.719 0.198,0.177 10 false *a 0.042,0.146 0.406,0.313 0.365,0.167 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in the selected intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.8 to 15.2 mm (0.583 to 0.598 in.)



g.
A194973

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A281402N01
1.208,0.667 0.76,0.323 0.76,0.323 1.146,1.167 true 0.438,0.219 0.896,0.479 0.458,0.26 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194975

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


Standard Bush Length:

46.8 to 47.2 mm (1.84 to 1.86 in.)


If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.
A281345C01
1.219,0.615 0.667,0.281 0.667,0.281 1.156,1.115 true 3,1.323 3.292,1.5 0.292,0.177 10 true *a 0.323,0.167 0.646,0.323 0.323,0.156 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in the selected exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.2 to 14.6 mm (0.559 to 0.575 in.)



g.
A281346

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11115A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 2 ring pins.


b.
A194963C07
2.229,2.365 3.229,2.542 1,0.177 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)