Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321409 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform inspection after repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A211988C18
2.229,1.333 2.229,1.083 false 1.833,0.281 2.208,0.521 0.375,0.24 10 false *b 1.646,1.708 2.021,1.958 0.375,0.25 10 false *c 2.177,1.365 2.552,1.615 0.375,0.25 10 false *a
*a Adhesive
*b Application Width
*c Distance


Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


Distance:

1.0 to 7.0 mm (0.0394 to 0.276 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Do not expose the spark plug tube to engine oil for at least 1 hour after installing it.




b.
A194971C16
2.396,3.156 2.844,3.385 0.448,0.229 10 true *a
*a Protrusion Height


Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard Protrusion Height:

112 mm (4.41 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 17159 2.INSTALL STUD BOLT

a.
A347104C01
0.344,1.583 0.719,1.823 0.375,0.24 12 false *A 2.125,1.594 2.5,1.833 0.375,0.24 12 false *B 0.833,2.167 1.146,2.365 0.313,0.198 10 false *a 1.302,2.385 1.615,2.583 0.313,0.198 10 false *b 0.833,2.635 1.146,2.833 0.313,0.198 10 false *c 2.594,2.167 2.906,2.365 0.313,0.198 10 false *d 3.01,2.323 3.323,2.521 0.313,0.198 10 false *e 2.615,2.615 2.927,2.813 0.313,0.198 10 false *c
*A Type A
*B Type B
*a 18 mm (0.709 in.)
*b 33 mm (1.30 in.)
*c 13 mm (0.512 in.)
*d 20 mm (0.787 in.)
*e 35 mm (1.38 in.)


Using an E7 or E8 "TORX" socket wrench, install the 5 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A194960

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11117F 4.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A194961

Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the 16 valve spring seats to the cylinder head sub-assembly.


Hide 13711E 6.INSTALL VALVE STEM OIL SEAL

a.
A124785C11
1.01,0.813 1.469,0.969 true 2.5,0.813 2.063,0.969 true 0.719,0.063 0.896,0.24 0.177,0.177 10 false *a 2.656,0.052 2.865,0.229 0.208,0.177 10 false *b 1.396,0.344 1.552,0.49 0.156,0.146 10 false *c 1.875,0.885 2.031,1.031 0.156,0.146 10 false *e 1.49,0.885 1.646,1.042 0.156,0.156 10 false *d
*a Intake Valve Stem Oil Seal
*b Exhaust Valve Stem Oil Seal
*c "NOK" Mark
*d Gray
*e Black


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Make sure to install each valve stem oil seal to the correct side. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve stem oil seals are gray and the exhaust valve stem oil seals are black.



b.
A194977C07
1.594,0.083 1.75,0.083 1.75,0.083 2.01,0.667 true 0.906,1.917 1.104,2.073 0.198,0.156 10 false *a 2.208,1.917 2.396,2.073 0.188,0.156 10 false *b 1.229,0 1.531,0.156 0.302,0.156 10 false SST
*a Correct
*b Incorrect


Using SST, push in the 8 intake valve stem oil seals and 8 exhaust valve stem oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the valve stem oil seals to be damaged or improperly seated.



Hide 13711 7.INSTALL INTAKE VALVE

a.
A285332C03
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.
A337757C01
2.448,0.333 2.667,0.167 2.667,0.167 2.75,0.167 false 2.417,1.333 2.5,1.333 2.5,1.333 2.646,1.042 false 2.771,0.083 3.083,0.24 0.313,0.156 10 false *a 2.25,1.26 2.563,1.417 0.313,0.156 10 false *b
*a Narrow
*b Wide


Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A337754N01
0.417,0.167 0.583,0.167 0.583,0.167 1.052,0.521 true 2.25,0.167 2.333,0.167 2.333,0.167 2.604,0.229 true 0.104,0.094 0.563,0.292 0.458,0.198 10 false SST 1.958,0.094 2.417,0.292 0.458,0.198 10 false SST

Using SST and wooden blocks, compress the compression spring and install the 8 valve spring retainer locks.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)


d.
A361737

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve spring retainer.



Hide 13715 8.INSTALL EXHAUST VALVE

a.
A285332C03
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A337758C01
0.875,0.344 0.667,0.167 0.667,0.167 0.583,0.167 false 0.656,1.052 0.333,1.167 0.333,1.167 0.25,1.167 false 0.417,0.094 0.729,0.25 0.313,0.156 10 false *a 0.104,1.083 0.417,1.24 0.313,0.156 10 false *b
*a Narrow
*b Wide


Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A337755N03
2.385,0.479 2.5,0.167 2.5,0.167 2.583,0.167 false 0.729,0.292 0.75,1.833 0.75,1.833 0.833,1.833 true 2.615,0.083 3.073,0.281 0.458,0.198 10 false SST 0.854,1.75 1.313,1.948 0.458,0.198 10 false SST

Using SST and wooden blocks, compress the compression spring and install the 8 valve spring retainer locks.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)


d.
A194981

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve spring retainer.