Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321410 CYLINDER BLOCK A

2AR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform inspection after repair after replacing the piston or piston ring.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A259693C05
1.271,2.458 1.688,2.698 0.417,0.24 10 false *a 1.302,2.854 1.625,3.073 0.323,0.219 10 false *b 1.875,2.635 2.948,2.844 1.073,0.208 10 false *c
*a 20 mm (0.787 in.)
*b 13 mm (0.512 in.)
*c 35 mm (1.38 in.)


Using an E8 "TORX" socket wrench, install the 2 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 15709 2.INSTALL NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A195789

Using a 5 mm hexagon wrench, install the 4 No. 2 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A195788

Using a 5 mm hexagon wrench, install the 2 No. 1 oil nozzle sub-assemblies with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13211 4.INSTALL PISTON

HINT:

Perform this procedure only when replacement of the piston pin hole snap ring (rear side) is necessary.


a.

Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.

HINT:

Tape the screwdriver tip before use.



b.

Gradually heat the piston to between 80 and 90°C (176 and 194°F).


c.

Apply a light coat of engine oil to the piston, piston pin and connecting rod sub-assembly.


d.
A285365C12
0.802,1.219 0.635,0.427 0.635,0.427 0.781,0.427 true 1.073,2.49 0.677,2.042 0.677,2.042 0.531,2.042 true 0.354,1.948 0.667,2.104 0.313,0.156 10 false *b 0.844,0.344 1.156,0.5 0.313,0.156 10 false *a
*a Cutout
*b Front Mark


Align the cutout of the piston and front mark of the connecting rod sub-assembly, insert the connecting rod sub-assembly into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the piston pin hole snap ring.

NOTICE:

Do not change the combination of the pistons and piston pins.



e.
A195811C16
1.771,1.688 2.26,1.688 true 1.26,1.885 0.875,1.885 true 0.667,1.781 0.844,1.948 0.177,0.167 10 false *a 2.281,1.583 2.458,1.75 0.177,0.167 10 false *1
*1 Piston Pin Hole Snap Ring
*a Cutout


Using a screwdriver, install a new piston pin hole snap ring (front side) on the other side of the piston pin hole.

HINT:
·

Be sure that the end gap of the piston pin hole snap ring is not aligned with the cutout of the piston.

·

Tape the screwdriver tip before use.




f.
A195813

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod sub-assembly back and forth on the piston pin. Check the fitting condition.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.



ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

HINT:
·

If abnormal movement is felt, replace the piston and piston pin as a set.

·

Perform inspection after repair after replacing the piston.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION





Hide 13011 5.INSTALL PISTON RING SET

a.
A341571C02
2.698,1.094 2.969,1.094 false 2.76,0.813 2.844,0.698 2.844,0.698 2.99,0.698 false 2.74,1.385 2.823,1.49 2.823,1.49 2.969,1.49 false 3.042,0.625 3.354,0.781 0.313,0.156 10 false *1 3.021,1.021 3.333,1.177 0.313,0.156 10 false *2 3.021,1.417 3.333,1.573 0.313,0.156 10 false *3
*1 Upper Oil Ring Side Rail
*2 Oil Ring Expander
*3 Lower Oil Ring Side Rail


Install the oil ring expander, upper oil ring side rail and lower oil ring side rail by hand.


b.
A297342C10
1.49,3.146 1.885,3.271 1.885,3.271 2.063,3.271 true 1.49,2.385 2.052,2.219 2.052,2.219 2.198,2.219 true 1.5,2.979 2.052,2.865 2.052,2.865 2.198,2.865 true 1.479,2.552 2.167,2.552 false 0.719,2.677 0.531,2.427 0.531,2.427 0.354,2.427 true 0.719,3.313 0.552,3.094 0.552,3.094 0.375,3.094 true 0.99,4.333 0.99,4.156 false 2.063,4.333 2.063,4.156 false 2.24,2.125 2.438,2.302 0.198,0.177 10 false *a 0.177,2.323 0.375,2.5 0.198,0.177 10 false *1 0.198,2.99 0.396,3.167 0.198,0.177 10 false *2 2,4.365 2.198,4.542 0.198,0.177 10 false *2 0.917,4.354 1.115,4.531 0.198,0.177 10 false *1 2.24,2.802 2.438,2.979 0.198,0.177 10 false *a 2.104,3.198 2.302,3.375 0.198,0.177 10 false *b 2.219,2.479 2.417,2.656 0.198,0.177 10 false *b
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Code Mark
*b Paint Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.

Piston Ring Mark:
Item Code Mark
No. 1 Compression Ring 1NA
No. 2 Compression Ring 2N


NOTICE:

Install the compression ring with the code mark facing upward.


HINT:

Perform "Inspection After Repair" after replacing the piston, piston ring.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13471A 6.INSTALL CRANKSHAFT PULLEY KEY

a.

Install the 2 crankshaft pulley keys to the crankshaft.


Hide 11711 7.INSTALL CRANKSHAFT BEARING

a.

Clean the main journal and both surfaces of the crankshaft bearings and No. 2 crankshaft bearings.


b.
A195816C10
1.614,3.832 1.787,3.984 0.173,0.151 10 *a 2.638,3.832 2.812,3.991 0.173,0.159 10 *b
*a Correct
*b Incorrect


Install the crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.




c.
A195817C18
2.333,3.229 1.948,2.583 1.948,2.583 1.802,2.583 false 0.552,3.719 0.76,3.948 0.208,0.229 10 false A 2.219,3.708 2.427,3.938 0.208,0.229 10 false B 1.635,2.49 2,2.729 0.365,0.24 10 false *a
*a Vernier Caliper


Install the No. 2 crankshaft bearings to the crankshaft bearing caps.


d.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and No. 2 crankshaft bearing edge.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the No. 2 crankshaft bearings or the contact surfaces.

·

Do not allow coolant to come into contact with the No. 2 crankshaft bearing inner surface.

·

If any coolant comes into contact with the No. 2 crankshaft bearing inner surface, replace the No. 2 crankshaft bearing with a new one.




Hide 11791 8.INSTALL CRANKSHAFT THRUST WASHER

a.
A195787C14
1.406,1.25 1.115,0.385 1.115,0.385 2.01,1.521 true 0.969,0.208 1.313,0.427 0.344,0.219 10 false *a
*a Oil Groove


Apply engine oil to the crankshaft thrust washers.


b.

Install the 2 crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 9.INSTALL CRANKSHAFT

a.
A259179C08
2.094,2.823 2.74,2.823 true 2.792,2.719 3,2.896 0.208,0.177 10 false *a
*a Front Mark


Apply engine oil to the crankshaft bearings, and place the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the No. 2 crankshaft bearings.


c.

Confirm the front marks and numbers, and install the 5 crankshaft bearing caps to the cylinder block sub-assembly with the front marks positioned as shown in the illustration.

HINT:

The crankshaft bearing cap bolts are tightened in 3 progressive steps.



d.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.


e.

Step 1:

i.
A285363N10
3.094,1.552 3.406,1.75 0.313,0.198 10 false 10 3.125,0.573 3.281,0.771 0.156,0.198 10 false 9 2.469,0.458 2.625,0.656 0.156,0.198 10 false 5 1.74,0.438 1.896,0.635 0.156,0.198 10 false 1 1.042,0.49 1.198,0.688 0.156,0.198 10 false 3 0.417,0.552 0.573,0.75 0.156,0.198 10 false 7 0.406,1.563 0.563,1.76 0.156,0.198 10 false 8 1.052,1.615 1.208,1.813 0.156,0.198 10 false 4 1.76,1.646 1.917,1.844 0.156,0.198 10 false 2 2.469,1.615 2.625,1.813 0.156,0.198 10 false 6

Uniformly install and tighten the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



f.

Step 2:

i.

Further tighten the 10 crankshaft bearing cap bolts again in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

If a crankshaft bearing cap bolt cannot be tightened to the specified torque, replace it.



g.

Step 3:

i.
A302206C04
2.26,0.729 2.635,0.406 true 2.667,0.281 2.979,0.438 0.313,0.156 10 false *a 1.552,0.385 1.865,0.542 0.313,0.156 10 false *b
*a Paint Mark
*b 90°
V100135

Front of Engine


Mark the front of the crankshaft bearing cap bolts with paint.


ii.

Tighten the 10 crankshaft bearing cap bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



h.

Check that the crankshaft turns smoothly.


Hide 13041 10.INSTALL CONNECTING ROD BEARING

a.
A195818C20
0.406,3.063 0.521,3.063 0.521,3.063 0.74,3.438 false 1.729,3.698 1.938,3.927 0.208,0.229 10 false A 2.865,3.698 3.073,3.927 0.208,0.229 10 false B 0.229,2.958 0.406,3.115 0.177,0.156 10 false *a
*a Vernier Caliper


Clean the connecting rod bearing contact surfaces of the connecting rod sub-assembly and connecting rod cap, and both surfaces of the 2 connecting rod bearings.


b.

Install the connecting rod bearings to the connecting rod sub-assembly and connecting rod cap.


c.

Using a vernier caliper, measure the distance between the edges of the connecting rod sub-assembly and connecting rod bearing, and the edges of the connecting rod cap and connecting rod bearing.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the connecting rod bearings or the contact surfaces.

·

Do not allow coolant to come into contact with the connecting rod bearing inner surface.

·

If any coolant comes into contact with the connecting rod bearing inner surface, replace the connecting rod bearing with a new one.




Hide 11.INSTALL PISTON WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.
A341171C07
0.75,0.188 1.219,0.406 0.469,0.219 10 false *a, *d 2.458,0.271 2.771,0.469 0.313,0.198 10 false *c 0.896,1.781 1.208,1.979 0.313,0.198 10 false *c 2.385,1.802 2.865,2.01 0.479,0.208 10 false *b, *e
*a No. 1 Compression Ring
*b No. 2 Compression Ring
*c Oil Ring Expander
*d Upper Oil Ring Side Rail
*e Lower Oil Ring Side Rail


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

Regardless of the front mark, the piston rings are positioned correctly if their ends are positioned opposite of each other.



c.
A195820C11
1.708,1.365 1.594,1.365 false 1.594,1.365 1.146,1.01 true 1.75,1.281 1.927,1.458 0.177,0.177 10 false *a
*a Front Mark


Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing the front of the engine.

NOTICE:

When inserting the piston with connecting rod into the cylinder block sub-assembly, make sure the No. 1 oil nozzle sub-assembly does not interfere with the connecting rod.



d.
A194880C20
2.917,1.792 1.49,0.917 true 2.938,1.708 3.115,1.865 0.177,0.156 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.

NOTICE:

Match the connecting rod cap with the connecting rod.



e.
A259170

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Temporarily install the connecting rod bolts.

HINT:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.

Alternately tighten the connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.
A304509C13
2.083,0.729 2.417,0.333 2.417,0.333 2.667,0.333 true 1.115,0.448 1.427,0.604 0.313,0.156 10 false *b 2.729,0.26 3.042,0.417 0.313,0.156 10 false *a
*a Paint Mark
*b 90°
V100135

Front of Engine


Step 2:

i.

Mark the front of the connecting rod bolts with paint.


ii.

Tighten the bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.