Home › General › SPECIFICATIONS › 2AR-FE ENGINE MECHANICAL › 2017.09–2021.02
RM33A0E _V1 General _065355 SPECIFICATIONS _0318912 2AR-FE ENGINE MECHANICAL F

SPECIFICATIONS  2AR-FE ENGINE MECHANICAL  TORQUE SPECIFICATIONS  


CAMSHAFT
Part Tightened N*m kgf*cm ft.*lbf in.*lbf
Camshaft timing exhaust gear assembly x No. 2 camshaft 85 867 63
Camshaft timing gear assembly x Camshaft 85 867 63
Camshaft housing sub-assembly x Cylinder head sub-assembly 27 275 20
Camshaft bearing cap x Camshaft housing sub-assembly 16 163 12
No. 1 chain tensioner assembly x Cylinder block sub-assembly 10 102 7
Timing chain cover plate x Timing chain cover sub-assembly 10 102 7
Engine wire x Engine A 10 102 7
B 9.8 100 87

CYLINDER HEAD GASKET
Part Tightened N*m kgf*cm ft.*lbf
Cylinder head sub-assembly x Cylinder block sub-assembly 1st 36 367 27
2nd 36 367 27
3rd Turn 90°
4th Turn 90°
Camshaft bearing cap x Camshaft housing sub-assembly 16 163 12
Camshaft housing sub-assembly x Cylinder head sub-assembly 27 275 20
Camshaft timing gear assembly x Camshaft 85 867 63
Camshaft timing exhaust gear assembly x No. 2 camshaft 85 867 63
No. 1 chain vibration damper x Cylinder block sub-assembly 21 214 15
Chain tensioner slipper x Cylinder head sub-assembly 21 214 15
No. 1 chain tensioner assembly x Cylinder block sub-assembly 10 102 7
Timing chain guide x Camshaft housing sub-assembly 21 214 15

FRONT CRANKSHAFT OIL SEAL
Part Tightened N*m kgf*cm ft.*lbf
Crankshaft pulley x Crankshaft 260 2651 192

REAR CRANKSHAFT OIL SEAL
Part Tightened N*m kgf*cm ft.*lbf
Drive plate and ring gear sub-assembly x Crankshaft 98 999 72

ENGINE ASSEMBLY
Part Tightened N*m kgf*cm ft.*lbf in.*lbf
No. 1 engine hanger and No. 2 engine hanger x Cylinder head sub-assembly 43 438 32
engine mounting bracket sub-assembly LH x Vehicle body 72 734 53
Engine mounting spacer x Vehicle body 72 734 53
Engine mounting insulator sub-assembly RH x Engine mounting spacer and Vehicle body 72 734 53
No. 1 bond cable x Engine mounting insulator sub-assembly RH 9.5 97 84
Bracket x Engine mounting insulator sub-assembly RH 8.0 82 71
Radiator reserve tank assembly x Vehicle body 5.0 51 44
Rear engine mounting insulator x Rear engine mounting bracket 72 734 53
Front engine mounting insulator x Front engine mounting bracket 72 734 53
Front frame assembly x Front engine mounting insulator and Rear engine mounting insulator 72 734 53
Front bumper extension sub-assembly RH and front bumper extension sub-assembly LH x Front frame assembly and vehicle body Bolt (A) 9.0 92 80
Bolt (B) 12.5 127 9
Bolt (C) 135 1377 100
Front suspension member rear bracket sub-assembly RH and front suspension member rear bracket sub-assembly LH x Front frame assembly and vehicle body Bolt (D) 17.5 178 13
Bolt (E) 135 1377 100
Nut 17.5 178 13
Engine mounting insulator LH x Engine mounting bracket sub-assembly LH 42 428 31
Engine mounting insulator sub-assembly RH x Engine mounting bracket RH Bolt 72 734 53
Nut 42 428 31
Wire harness x Vehicle body 8.0 82 71
Wire harness x Engine room relay block and junction block assembly 8.0 82 71
Wire harness x Vehicle body 10 102 7
Transmission control cable assembly x Transmission control shaft lever 12 122 9
Battery clamp sub-assembly x Engine mounting insulator LH 18.5 189 14
Wire harness x Positive (+) battery terminal 7.6 77 67
Inlet air cleaner assembly x Vehicle body 8.0 82 71
Front lower bumper absorber x Vehicle body 7.5 76 66
Front fender apron seal LH x Vehicle body 7.5 76 66
Front fender apron seal RH x Vehicle body 7.5 76 66
No. 1 engine under cover x Vehicle body 7.5 76 66

ENGINE UNIT
Part Tightened N*m kgf*cm ft.*lbf in.*lbf
Stud bolt x Cylinder head cover sub-assembly 5.0 51 44
Stud bolt x Camshaft housing sub-assembly 6.5 66 58
Stud bolt x Stiffening crankcase assembly Stud bolt (A) 9.5 97 84
Stud bolt (B) 4.0 41 35
Stud bolt x Cylinder block sub-assembly 8.5 87 75
Engine balancer assembly x Stiffening crankcase 24 245 18
Stiffening crankcase assembly x Cylinder block sub-assembly Bolt (A) 24 245 18
except Bolt (A) 43 438 32
No. 1 oil pan baffle plate x Stiffening crankcase assembly 10 102 7
Oil strainer sub-assembly x Stiffening crankcase assembly 9.0 92 80
Oil pan sub-assembly x Stiffening crankcase 10 102 7
Oil pan drain plug x Oil pan sub-assembly 40 408 30
Oil pump relief valve plug x Timing chain cover sub-assembly 37.5 382 28
Cylinder head cover sub-assembly x Camshaft housing sub-assembly 12 122 9
w/o Oil Cooler:
Stud bolt x Water inlet housing
4.4 45 39
w/ Oil Cooler:
Stud bolt x Water inlet housing
Stud bolt (A), (B) 4.4 45 39
Stud bolt (C) 4.0 41 35
Water inlet housing x Cylinder block sub-assembly 43 438 32
V-ribbed belt tensioner assembly x Water inlet housing 21 214 15
Wire harness clamp bracket x Water inlet housing 10 102 7
No. 1 water by-pass pipe x Water inlet housing and Cylinder block sub-assembly 10 102 7
Separator case x Ventilation case sub-assembly 10 102 7
Ventilation case sub-assembly x Cylinder block sub-assembly 21 214 15
Engine cover joint x Cylinder head cover sub-assembly and Camshaft housing sub-assembly 10 102 7
Sensor wire x Cylinder block sub-assembly 21 214 15
No. 1 compressor mounting bracket x Cylinder block sub-assembly and Stiffening crankcase assembly 21 214 15
Drive shaft bearing bracket x Cylinder block sub-assembly 63.7 650 47
for Type A:
Compressor assembly with pulley x No. 1 compressor mounting bracket
Stud bolt 10 102 7
Bolt and Nut 24.5 250 18
for Type B:
Compressor assembly with pulley x No. 1 compressor mounting bracket
24.5 250 18
Wire harness clamp bracket x Cylinder head cover sub-assembly 10 102 7
Wire harness clamp bracket x Cylinder head cover sub-assembly 10 102 7
Wire harness clamp bracket x Timing chain cover sub-assembly 10 102 7
Engine oil level dipstick guide x Water inlet housing 10 102 7

CYLINDER HEAD
Part Tightened N*m kgf*cm ft.*lbf in.*lbf
Stud bolt x Cylinder head sub-assembly 6.5 66 58
No. 1 straight screw plug x Cylinder head sub-assembly 44 449 32
No. 2 straight screw plug x Cylinder head sub-assembly 78 795 58

CYLINDER BLOCK
Part Tightened N*m kgf*cm ft.*lbf in.*lbf
Stud bolt x Cylinder block sub-assembly 6.5 66 58
No. 2 oil nozzle sub-assembly x Cylinder block sub-assembly 10 102 7
No. 1 oil nozzle sub-assembly x Cylinder block sub-assembly 10 102 7
Crankshaft bearing cap x Cylinder block sub-assembly Step 1 20 204 15
Step 2 40 408 30
Step 3 Turn 90°
Connecting rod cap x Connecting rod sub-assembly Step 1 40 408 30
Step 2 Turn 90°