Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E287097E85
1.021,0.792 2.854,0.99 1.833,0.198 10 false from Battery 0.802,1.573 2.635,1.771 1.833,0.198 10 false from ACC Relay 0.49,2.375 2.323,2.573 1.833,0.198 10 false from IG1-NO. 1 Relay 3.573,0.969 5.406,1.167 1.833,0.198 10 false TV 3.375,1.75 5.208,1.948 1.833,0.198 10 false ECU-ACC 3.229,2.573 4.948,2.771 1.719,0.198 10 false ECU-IG1 NO. 4 5.323,3.625 7.031,4.135 1.708,0.51 10 false Radio and Display Receiver Assembly 5.469,0.802 5.781,1 0.313,0.198 10 false K3 5.469,1.583 5.781,1.781 0.313,0.198 10 false K3 5.469,2.375 5.781,2.573 0.313,0.198 10 false K2 5.469,3.167 5.781,3.365 0.313,0.198 10 false K3 5.521,2.99 5.833,3.188 0.313,0.198 10 false 1 5.5,2.198 5.813,2.396 0.313,0.198 10 false 19 5.51,1.385 5.823,1.583 0.313,0.198 10 false 15 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the K3 and K2 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K3-4 (+B1) - K3-1 (GND1) Always 11 to 14 V
K3-15 (ACC1) - K3-1 (GND1) Ignition switch ACC 11 to 14 V
K2-19 (IG) - K3-1 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR