Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2017.09–2018.04
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume based on vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are sent from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E375733E01
0.302,1.677 3.406,2.042 3.104,0.365 10 false Skid control ECU (Brake Actuator Assembly) 1.104,3.719 4.208,4.083 3.104,0.365 10 false ECM 0.344,5.313 3.448,5.677 3.104,0.365 10 false Radio and Display Receiver Assembly*4 4.073,3.76 7.094,4.125 3.021,0.365 10 false Certification ECU (Smart Key ECU Assembly)*6 5.135,2.083 7,2.438 1.865,0.354 10 false Combination Meter Assembly 6.031,0.406 6.417,0.677 0.385,0.271 10 false 12 V 5.531,0.729 5.917,1 0.385,0.271 10 false SI 5.531,1.26 5.917,1.531 0.385,0.271 10 false +S 5.344,0.729 5.729,1 0.385,0.271 10 false 5 5.323,1.26 5.708,1.531 0.385,0.271 10 false 6 1.823,0.729 2.208,1 0.385,0.271 10 false 34 1.438,0.74 1.823,1.01 0.385,0.271 10 false SP1 0.313,1.521 0.698,1.792 0.385,0.271 10 false A34 1.396,3.146 4.5,3.51 3.104,0.365 10 false SPD 1.865,3.052 2.104,3.313 0.24,0.26 10 false 42 4.073,3.615 4.615,3.854 0.542,0.24 10 false K62 5.271,3.146 5.813,3.385 0.542,0.24 10 false 19 5.542,3.146 5.938,3.417 0.396,0.271 10 false SPD 5.563,4.698 5.958,4.969 0.396,0.271 10 false SPD 1.427,4.677 1.823,4.948 0.396,0.271 10 false SPD 2.271,3.052 2.51,3.313 0.24,0.26 10 false 39 1.833,3.25 2.125,3.458 0.292,0.208 10 false A24 2.25,3.25 2.594,3.406 0.344,0.156 10 false A23 1.813,4.677 2.052,4.938 0.24,0.26 10 false 27 0.354,5.156 0.75,5.427 0.396,0.271 10 false K3 5.458,5.281 6.583,5.656 1.125,0.375 10 false Navigation ECU*7 5.167,5.281 5.563,5.552 0.396,0.271 10 false K17 5.344,4.688 5.74,4.958 0.396,0.271 10 false 9 4.844,2.094 5.156,2.302 0.313,0.208 10 false K21 2.635,3.25 2.948,3.479 0.313,0.229 10 false A22 2.677,3.052 2.917,3.313 0.24,0.26 10 false 44 1.854,3.448 2.094,3.708 0.24,0.26 10 false *1 2.271,3.458 2.51,3.719 0.24,0.26 10 false *2 2.667,3.448 2.906,3.708 0.24,0.26 10 false *3 4.052,6.115 7.156,6.479 3.104,0.365 10 false *1: for A25A-FKS 4.052,6.458 7.156,6.823 3.104,0.365 10 false *2: for 2GR-FKS 4.052,6.802 7.156,7.167 3.104,0.365 10 false *3: for 2AR-FE 4.052,7.146 7.156,7.51 3.104,0.365 10 false *4: w/ No. 1 Stereo Jack Adapter Assembly 4.052,7.833 7.156,8.198 3.104,0.365 10 false *6: w/ Smart Entry and Start System 4.052,7.49 7.156,7.854 3.104,0.365 10 false *5: for 9 Speakers 0.219,6.854 3.323,7.219 3.104,0.365 10 false Stereo Component Amplifier Assembly*5 1.427,6.208 1.823,6.479 0.396,0.271 10 false SPD 4.052,8.177 7.156,8.542 3.104,0.365 10 false *7: w/ Navigation System 0.229,6.677 0.625,6.948 0.396,0.271 10 false K10 1.802,6.208 2.042,6.469 0.24,0.26 10 false 11


CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

While driving the vehicle, compare the value displayed for "SPEED" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C74
1.479,0.438 1.896,0.656 0.417,0.219 2.542,1.99 2.208,1.344 false 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.563,0.469 1.958,0.677 0.396,0.208 10 false K21 2.49,2 2.802,2.198 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal K21-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
E360497C01
1.552,0.344 1.885,0.583 0.333,0.24 0.781,2.104 1.135,1.594 false 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.646,0.375 1.958,0.573 0.313,0.198 10 false K3 0.646,2.115 1.083,2.344 0.438,0.229 10 false SPD 2.875,3.667 3.313,3.896 0.438,0.229 10 false GND 1.156,3.948 1.594,4.177 0.438,0.229 10 false A
*a Component with harness connected
(Radio and Display Receiver Assembly)


Check the input waveform.

i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal K3-27 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K3-27 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR