Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E360461E06
1.344,0.5 1.521,0.677 0.177,0.177 10 false 9 0.875,1.458 1.49,1.656 0.615,0.198 10 false UDO+ 0.906,2.219 1.521,2.417 0.615,0.198 10 false UJSS 5.906,2.219 6.521,2.417 0.615,0.198 10 false USG1 5.906,1.458 6.521,1.656 0.615,0.198 10 false US1+ 5.906,0.656 6.521,0.854 0.615,0.198 10 false US1- 0.458,2.667 1.073,2.865 0.615,0.198 10 false K5 0.458,2.854 1.625,3.208 1.167,0.354 10 false No. 1 Stereo Jack Adapter Assembly 2.479,3.271 5.083,3.5 2.604,0.229 10 false : Data Signal (USB Communication Line) 3.271,1.76 3.906,1.979 0.635,0.219 10 false (Shielded) 5.844,2.667 6.458,2.865 0.615,0.198 10 false K135 5.833,2.875 7.031,3.344 1.198,0.469 10 false Radio and Display Receiver Assembly 5.729,0.542 5.906,0.719 0.177,0.177 10 false 2 1.333,1.323 1.51,1.5 0.177,0.177 10 false 10 1.354,2.094 1.531,2.271 0.177,0.177 10 false 12 5.75,2.115 5.927,2.292 0.177,0.177 10 false 5 5.74,1.323 5.917,1.5 0.177,0.177 10 false 3 0.906,0.656 1.521,0.854 0.615,0.198 10 false UDO-

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the K135 radio and display receiver assembly connector.


b.

Disconnect the K5 No. 1 stereo jack adapter assembly connector.


c.
E360495C08
1.563,2.219 1.906,2.458 0.344,0.24 1.542,0.208 1.958,0.479 0.417,0.271 2.135,1.938 1.781,1.49 false 1.844,1.354 2.26,1.5 false 1.115,1.667 1.583,1.313 false 1.417,4.083 1.656,3.76 false 0.969,4.063 1.646,3.667 false 2.135,4 1.792,3.656 false 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.76,1.625 1.188,1.833 0.427,0.208 10 false US1+ 2.188,1.906 2.677,2.146 0.49,0.24 10 false USG1 2.313,1.438 2.729,1.688 0.417,0.25 10 false US1- 0.635,4.021 1.031,4.281 0.396,0.26 10 false UDO- 1.24,4.094 1.74,4.354 0.5,0.26 10 false UJSS 2.167,3.938 2.604,4.198 0.438,0.26 10 false UDO+ 1.583,0.271 2.042,0.469 0.458,0.198 10 false K135 1.646,2.271 1.958,2.469 0.313,0.198 10 false K5
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K135-2 (US1-) - K5-9 (UDO-) Always Below 1 Ω
K135-3 (US1+) - K5-10 (UDO+) Always Below 1 Ω
K135-5 (USG1) - K5-12 (UJSS) Always Below 1 Ω
K135-2 (US1-) or K5-9 (UDO-) - Body ground Always 10 kΩ or higher
K135-3 (US1+) or K5-10 (UDO+) - Body ground Always 10 kΩ or higher
K135-5 (USG1) or K5-12 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR