Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2017.09–2018.04
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.


WIRING DIAGRAM

w/o Sliding Roof


E377468E04
0.521,3.281 1.906,3.833 1.385,0.552 10 false Telephone Microphone Assembly 2.729,3.323 3.865,3.844 1.135,0.521 10 false Roof Console Box Sub-assembly 5.354,3.385 7.031,3.865 1.677,0.479 10 false Radio and Display Receiver Assembly 2.542,2.854 2.917,3.208 0.375,0.354 10 false B 2.531,1.917 2.906,2.271 0.375,0.354 10 false B 2.531,1.448 2.906,1.802 0.375,0.354 10 false B 2.531,0.969 2.906,1.323 0.375,0.354 10 false B 3.719,2.656 4.094,3.01 0.375,0.354 10 false 12 3.719,2.156 4.094,2.51 0.375,0.354 10 false 4 3.708,1.24 4.073,1.594 0.365,0.354 10 false 10 3.719,1.708 4.083,2.063 0.365,0.354 10 false 11 3.75,0.74 4.115,1.094 0.365,0.354 10 false 9 2.542,0.76 2.906,1.115 0.365,0.354 10 false 5 2.542,1.25 2.906,1.604 0.365,0.354 10 false 3 2.552,1.719 2.917,2.073 0.365,0.354 10 false 2 2.552,2.656 2.917,3.01 0.365,0.354 10 false 1 3.188,2.854 3.625,3.177 0.438,0.323 10 false SNS2 3.26,2.344 3.677,2.604 0.417,0.26 10 false GND 3.188,1.896 3.677,2.198 0.49,0.302 10 false MCO- 3.146,1.427 3.635,1.76 0.49,0.333 10 false MCO+ 3.146,0.938 3.635,1.271 0.49,0.333 10 false MACC 5.708,0.969 6.198,1.302 0.49,0.333 10 false MACC 5.698,1.448 6.188,1.781 0.49,0.333 10 false MIN+ 5.708,1.917 6.198,2.25 0.49,0.333 10 false MIN- 5.698,2.385 6.188,2.719 0.49,0.333 10 false SGND 5.708,2.865 6.146,3.188 0.438,0.323 10 false SNS2 5.479,2.75 5.854,3.104 0.375,0.354 10 false 25 5.49,2.281 5.865,2.635 0.375,0.354 10 false 24 5.479,1.802 5.854,2.156 0.375,0.354 10 false 22 5.479,1.323 5.854,1.677 0.375,0.354 10 false 21 5.469,0.844 5.844,1.198 0.375,0.354 10 false 23 5.302,3.177 5.698,3.604 0.396,0.427 10 false K2 3.667,0.958 4.042,1.313 0.375,0.354 10 false V13 4.375,2.208 5.177,2.479 0.802,0.271 10 false (Shielded) 3.677,1.427 4.052,1.781 0.375,0.354 10 false V13 3.667,1.906 4.042,2.26 0.375,0.354 10 false V13 3.677,2.354 4.052,2.708 0.375,0.354 10 false V13 3.667,2.844 4.042,3.198 0.375,0.354 10 false V13


w/ Sliding Roof


E377468E01
0.521,3.281 1.906,3.833 1.385,0.552 10 false Telephone Microphone Assembly 2.729,3.323 3.865,3.844 1.135,0.521 10 false Roof Console Box Sub-assembly 5.354,3.385 7.031,3.865 1.677,0.479 10 false Radio and Display Receiver Assembly 2.542,2.854 2.917,3.208 0.375,0.354 10 false B 2.531,1.917 2.906,2.271 0.375,0.354 10 false B 2.531,1.448 2.906,1.802 0.375,0.354 10 false B 2.531,0.969 2.906,1.323 0.375,0.354 10 false B 3.677,0.948 4.052,1.302 0.375,0.354 10 false V14 3.667,1.438 4.042,1.792 0.375,0.354 10 false V14 3.667,1.906 4.042,2.26 0.375,0.354 10 false V14 3.656,2.354 4.031,2.708 0.375,0.354 10 false V14 3.677,2.854 4.052,3.208 0.375,0.354 10 false V14 3.75,2.656 4.125,3.01 0.375,0.354 10 false 6 3.719,2.156 4.094,2.51 0.375,0.354 10 false 15 3.74,1.24 4.104,1.594 0.365,0.354 10 false 8 3.75,1.708 4.115,2.063 0.365,0.354 10 false 7 3.75,0.74 4.115,1.094 0.365,0.354 10 false 9 2.542,0.76 2.906,1.115 0.365,0.354 10 false 5 2.542,1.25 2.906,1.604 0.365,0.354 10 false 3 2.552,1.719 2.917,2.073 0.365,0.354 10 false 2 2.552,2.656 2.917,3.01 0.365,0.354 10 false 1 3.188,2.854 3.625,3.177 0.438,0.323 10 false SNS2 3.26,2.344 3.677,2.604 0.417,0.26 10 false GND 3.188,1.896 3.677,2.198 0.49,0.302 10 false MCO- 3.146,1.427 3.635,1.76 0.49,0.333 10 false MCO+ 3.146,0.938 3.635,1.271 0.49,0.333 10 false MACC 5.708,0.969 6.198,1.302 0.49,0.333 10 false MACC 5.698,1.448 6.188,1.781 0.49,0.333 10 false MIN+ 5.708,1.917 6.198,2.25 0.49,0.333 10 false MIN- 5.698,2.385 6.188,2.719 0.49,0.333 10 false SGND 5.708,2.865 6.146,3.188 0.438,0.323 10 false SNS2 5.479,2.75 5.854,3.104 0.375,0.354 10 false 25 5.49,2.281 5.865,2.635 0.375,0.354 10 false 24 5.479,1.802 5.854,2.156 0.375,0.354 10 false 22 5.479,1.323 5.854,1.677 0.375,0.354 10 false 21 5.469,0.844 5.844,1.198 0.375,0.354 10 false 23 5.302,3.177 5.698,3.604 0.396,0.427 10 false K2 4.375,2.208 5.094,2.531 0.719,0.323 10 false (Shielded)


CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
NG (w/ Sliding Roof) A
NG (w/o Sliding Roof) B
OK C



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V14-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V14-8 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V14-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V14-8 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.
E360498C01
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 2.271,2.896 1.927,2.156 false 1.198,2.833 1.813,2.146 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360501C01
1.76,1.24 1.688,0.698 false 1.969,1.24 2.208,0.719 false 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.521,0.531 1.948,0.74 0.427,0.208 10 false MCO- 2.104,0.552 2.531,0.771 0.427,0.219 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371629C01
1.563,0.188 2.01,0.427 0.448,0.24 1.167,0.49 1.625,1.333 false 2.219,0.448 1.771,1.333 false 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 1.656,0.24 1.969,0.438 0.313,0.198 10 false V14 0.802,0.302 1.313,0.51 0.51,0.208 10 false MCO+ 2.281,0.313 2.792,0.521 0.51,0.208 10 false MCO- 2.823,3.438 3.333,3.646 0.51,0.208 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V14-8 (MCO+) - V14-7 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C05
1.427,2.792 1.885,3.052 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.677,1.573 1.417,0.865 false 1.833,1.552 2.094,0.854 false 2.448,2.448 2.708,1.75 false 1.031,0.74 1.542,1.01 0.51,0.271 10 false MCO+ 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.708 0.531,2.906 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.573,2.833 2.052,3.052 0.479,0.219 10 false B 2.167,0.75 2.708,0.969 0.542,0.219 10 false MCO- 2.135,2.396 2.677,2.615 0.542,0.219 10 false GND
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-8 (MCO+) - B-3 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-8 (MCO+) or B-3 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C06
1.427,2.938 1.885,3.198 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.969,1.583 2.229,0.885 false 2.5,2.281 2.708,1.75 false 1.813,1.583 1.375,0.917 false 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.896 0.531,3.094 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.583,2.979 2.063,3.198 0.479,0.219 10 false B 2.302,0.781 2.844,1 0.542,0.219 10 false SNS2 2.188,2.281 2.729,2.5 0.542,0.219 10 false GND 0.979,0.802 1.521,1.021 0.542,0.219 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-6 (SNS2) - B-1 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-6 (SNS2) or B-1 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V13 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V13-12 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V13-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V13-10 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V13-11 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V13-12 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V13-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V13-10 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V13-11 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.
E360498C03
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.188,2.885 1.927,2.146 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

10.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360499C01
1.74,1.698 1.573,1.385 false 1.219,1.719 1.458,1.385 false 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.031,1.719 1.479,1.958 0.448,0.24 10 false SNS2 1.667,1.698 2.156,1.958 0.49,0.26 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371634C03
1.448,0.177 1.906,0.458 0.458,0.281 2.063,2.135 1.792,1.448 false 1.198,2.146 1.542,1.427 false 0.156,0.167 0.552,0.375 0.396,0.208 10 false *a 1.542,0.24 1.938,0.448 0.396,0.208 10 false V13 0.823,2.104 1.323,2.302 0.5,0.198 10 false MCO- 2.115,2.083 2.615,2.281 0.5,0.198 10 false MCO+ 2.813,3.448 3.313,3.646 0.5,0.198 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 10 (MCO+) and 11 (MCO-) of the V13 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V13-10 (MCO+) - V13-11 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C11
1.5,2.75 1.917,3 0.417,0.25 1.417,0.583 1.833,0.833 0.417,0.25 1.042,1.531 0.771,0.969 false 1.51,2.083 1.625,1.74 false 2.156,2.208 1.917,1.771 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.198,2.073 1.708,2.354 0.51,0.281 10 false MCO- 2.208,2.177 2.719,2.458 0.51,0.281 10 false MCO+ 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.656,2.792 2.167,3.073 0.51,0.281 10 false B
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-10 (MCO+) - B-3 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-10 (MCO+) or B-3 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C12
1.458,2.75 1.885,3.01 0.427,0.26 1.417,0.563 1.844,0.823 0.427,0.26 1.042,1.531 0.771,0.969 false 1.417,2.073 1.531,1.729 false 1.854,2.125 1.646,1.75 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.052,2.083 1.563,2.365 0.51,0.281 10 false SNS2 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.604,2.792 2.115,3.073 0.51,0.281 10 false B 1.896,2.094 2.406,2.375 0.51,0.281 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-12 (SNS2) - B-1 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-12 (SNS2) or B-1 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY