Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E336580E15
0.594,2.052 1.813,2.49 1.219,0.438 10 false Stereo Component Amplifier Assembly 0.604,1.885 0.969,2.115 0.365,0.229 10 false K10 5.135,1.875 5.5,2.104 0.365,0.229 10 false K3 5.135,2.042 6.833,2.542 1.698,0.5 10 false Radio and Display Receiver Assembly 5.542,1.021 6,1.229 0.458,0.208 10 false MUT1 5.281,0.927 5.552,1.167 0.271,0.24 10 false 25 1.74,0.917 2.01,1.156 0.271,0.24 10 false 1 1.26,1.021 1.75,1.229 0.49,0.208 10 false MUTE

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C63
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.844 1.927,1 0.333,0.156 10 false K10 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K10-1 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Changing modes
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Disconnect the K10 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-25 (MUT1) - K10-1 (MUTE) Always Below 1 Ω
K3-25 (MUT1) or K10-1 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Reconnect the K10 stereo component amplifier assembly connector.


b.
E382034C01
1.51,0.198 1.927,0.427 0.417,0.229 2.375,2.906 2.135,2.385 false 1.635,0.229 1.948,0.427 0.313,0.198 10 false K3 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 2.333,2.927 2.865,3.188 0.531,0.26 10 false MUT1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K3-25 (MUT1) - Body ground Ignition switch ACC, audio system is playing 3.5 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY