Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication.

If a short to +B or short to ground occurs in an AVC-LAN communication line, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

for 9 Speakers


E276615E21
2.958,2.208 4.938,2.396 1.979,0.188 10 false : AVC-LAN Communication Line 1.01,1.469 1.469,1.667 0.458,0.198 10 false K10 5.094,0.583 5.552,0.781 0.458,0.198 10 false TX1+ 5.052,1.615 6.26,2.063 1.208,0.448 10 false Radio and Display Receiver Assembly 0.99,1.625 2.198,2.198 1.208,0.573 10 false Stereo Component Amplifier Assembly 5.052,1.469 5.51,1.667 0.458,0.198 10 false K3 5.104,0.979 5.563,1.177 0.458,0.198 10 false TX1- 4.906,0.448 5.104,0.625 0.198,0.177 10 false 5 4.906,0.833 5.104,1.01 0.198,0.177 10 false 6 1.844,0.573 2.302,0.771 0.458,0.198 10 false TX+ 1.875,0.948 2.115,1.156 0.24,0.208 10 false TX- 2.177,0.448 2.375,0.625 0.198,0.177 10 false 8 2.177,0.833 2.375,1.01 0.198,0.177 10 false 7


w/ Cooler Control Switch Assembly


E276615E22
2.958,2.208 4.938,2.396 1.979,0.188 10 false : AVC-LAN Communication Line 1.01,1.469 1.469,1.667 0.458,0.198 10 false Z1 5.094,0.583 5.552,0.781 0.458,0.198 10 false TX1+ 5.052,1.615 6.26,2.063 1.208,0.448 10 false Radio and Display Receiver Assembly 0.99,1.625 2.323,2.208 1.333,0.583 10 false Cooler Control Switch Assembly 5.052,1.469 5.51,1.667 0.458,0.198 10 false K3 5.104,0.979 5.563,1.177 0.458,0.198 10 false TX1- 4.906,0.448 5.104,0.625 0.198,0.177 10 false 5 4.906,0.833 5.104,1.01 0.198,0.177 10 false 6 1.844,0.573 2.302,0.771 0.458,0.198 10 false TX+ 1.875,0.948 2.115,1.156 0.24,0.208 10 false TX- 2.177,0.813 2.375,0.99 0.198,0.177 10 false 8 2.177,0.427 2.375,0.604 0.198,0.177 10 false 7


CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for 9 Speakers A
w/ Cooler Control Switch Assembly B




A

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

B

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.


b.
E382042C01
1.615,0.333 2.021,0.583 0.406,0.25 2.323,1.729 2.563,1.25 false 2.906,1.708 2.698,1.25 false 2.844,1.771 3.302,2.01 0.458,0.24 10 false TX1+ 2.188,1.76 2.646,2 0.458,0.24 10 false TX1- 1.74,0.385 2.198,0.625 0.458,0.24 10 false K3 0.135,0.125 0.594,0.365 0.458,0.24 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-5 (TX1+) - K3-6 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Disconnect the K10 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-8 (TX+) - K3-5 (TX1+) Always Below 1 Ω
K10-7 (TX-) - K3-6 (TX1-) Always Below 1 Ω
K10-8 (TX+) or K3-5 (TX1+) - Body ground Always 10 kΩ or higher
K10-7 (TX-) or K3-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.


b.
E382042C01
1.615,0.333 2.021,0.583 0.406,0.25 2.323,1.729 2.563,1.25 false 2.906,1.708 2.698,1.25 false 2.844,1.771 3.302,2.01 0.458,0.24 10 false TX1+ 2.188,1.76 2.646,2 0.458,0.24 10 false TX1- 1.74,0.385 2.198,0.625 0.458,0.24 10 false K3 0.135,0.125 0.594,0.365 0.458,0.24 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-5 (TX1+) - K3-6 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Disconnect the Z1 cooler control switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-7 (TX+) - K3-5 (TX1+) Always Below 1 Ω
Z1-8 (TX-) - K3-6 (TX1-) Always Below 1 Ω
Z1-7 (TX+) or K3-5 (TX1+) - Body ground Always 10 kΩ or higher
Z1-8 (TX-) or K3-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY