Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2017.09–2018.04
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E375733E01
0.302,1.677 3.406,2.042 3.104,0.365 10 false Skid control ECU (Brake Actuator Assembly) 1.104,3.719 4.208,4.083 3.104,0.365 10 false ECM 0.344,5.313 3.448,5.677 3.104,0.365 10 false Radio and Display Receiver Assembly*4 4.073,3.76 7.094,4.125 3.021,0.365 10 false Certification ECU (Smart Key ECU Assembly)*6 5.135,2.083 7,2.438 1.865,0.354 10 false Combination Meter Assembly 6.031,0.406 6.417,0.677 0.385,0.271 10 false 12 V 5.531,0.729 5.917,1 0.385,0.271 10 false SI 5.531,1.26 5.917,1.531 0.385,0.271 10 false +S 5.344,0.729 5.729,1 0.385,0.271 10 false 5 5.323,1.26 5.708,1.531 0.385,0.271 10 false 6 1.823,0.729 2.208,1 0.385,0.271 10 false 34 1.438,0.74 1.823,1.01 0.385,0.271 10 false SP1 0.313,1.521 0.698,1.792 0.385,0.271 10 false A34 1.396,3.146 4.5,3.51 3.104,0.365 10 false SPD 1.865,3.052 2.104,3.313 0.24,0.26 10 false 42 4.073,3.615 4.615,3.854 0.542,0.24 10 false K62 5.271,3.146 5.813,3.385 0.542,0.24 10 false 19 5.542,3.146 5.938,3.417 0.396,0.271 10 false SPD 5.563,4.698 5.958,4.969 0.396,0.271 10 false SPD 1.427,4.677 1.823,4.948 0.396,0.271 10 false SPD 2.271,3.052 2.51,3.313 0.24,0.26 10 false 39 1.833,3.25 2.125,3.458 0.292,0.208 10 false A24 2.25,3.25 2.594,3.406 0.344,0.156 10 false A23 1.813,4.677 2.052,4.938 0.24,0.26 10 false 27 0.354,5.156 0.75,5.427 0.396,0.271 10 false K3 5.458,5.281 6.583,5.656 1.125,0.375 10 false Navigation ECU*7 5.167,5.281 5.563,5.552 0.396,0.271 10 false K17 5.344,4.688 5.74,4.958 0.396,0.271 10 false 9 4.844,2.094 5.156,2.302 0.313,0.208 10 false K21 2.635,3.25 2.948,3.479 0.313,0.229 10 false A22 2.677,3.052 2.917,3.313 0.24,0.26 10 false 44 1.854,3.448 2.094,3.708 0.24,0.26 10 false *1 2.271,3.458 2.51,3.719 0.24,0.26 10 false *2 2.667,3.448 2.906,3.708 0.24,0.26 10 false *3 4.052,6.115 7.156,6.479 3.104,0.365 10 false *1: for A25A-FKS 4.052,6.458 7.156,6.823 3.104,0.365 10 false *2: for 2GR-FKS 4.052,6.802 7.156,7.167 3.104,0.365 10 false *3: for 2AR-FE 4.052,7.146 7.156,7.51 3.104,0.365 10 false *4: w/ No. 1 Stereo Jack Adapter Assembly 4.052,7.833 7.156,8.198 3.104,0.365 10 false *6: w/ Smart Entry and Start System 4.052,7.49 7.156,7.854 3.104,0.365 10 false *5: for 9 Speakers 0.219,6.854 3.323,7.219 3.104,0.365 10 false Stereo Component Amplifier Assembly*5 1.427,6.208 1.823,6.479 0.396,0.271 10 false SPD 4.052,8.177 7.156,8.542 3.104,0.365 10 false *7: w/ Navigation System 0.229,6.677 0.625,6.948 0.396,0.271 10 false K10 1.802,6.208 2.042,6.469 0.24,0.26 10 false 11

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C77
1.5,0.417 1.917,0.667 0.417,0.25 2.542,1.99 2.208,1.344 false 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.583,0.458 1.979,0.667 0.396,0.208 10 false K21 2.49,2 2.802,2.198 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connectors still connected.


ii.

Connect an oscilloscope to terminal K21-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265796C21
1.604,0.385 2.01,0.667 0.406,0.281 1.146,1.958 1.344,1.313 false 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.688,0.427 2,0.625 0.313,0.198 10 false K10 1,1.99 1.469,2.229 0.469,0.24 10 false SPD 4.573,1.813 4.885,2.01 0.313,0.198 10 false A 5.969,1.563 6.469,1.854 0.5,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)
- -


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal K10-11 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K10-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR