Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065381 METER / GAUGE / DISPLAY _0323396 METER / GAUGE SYSTEM G

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 83100 1.INSPECT COMBINATION METER ASSEMBLY

a.

Inspect speedometer operation

NOTICE:
·

The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.

·

Data List values of the skid control ECU (brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.

·

If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.



i.

Warm up the engine.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


vi.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
Reference km/h (for RHD without Front Fog Light)
GTS Indication (km/h) Acceptable Range (km/h)
20 20.5 to 24.6
40 41.1 to 45.2
60 61.6 to 65.7
80 82.2 to 86.3
100 102.8 to 106.9
120 123.3 to 127.4
140 143.9 to 148.0
160 164.4 to 168.5
180 185.0 to 189.1
200 205.6 to 209.7
220 226.1 to 230.2
240 246.7 to 250.8

Reference km/h (for LHD, RHD with Front Fog Light)
GTS Indication (km/h) Acceptable Range (km/h)
20 21 to 25
40 41.7 to 46.2
60 62.7 to 67.2
80 83.4 to 88.4
100 104.3 to 109.3
120 125.1 to 130.6
140 145.8 to 151.8
160 166.2 to 173.2
180 186.9 to 194.5
200 207.7 to 215.7
220 228.4 to 236.8
240 249.2 to 258.0

OK:

Speedometer reading is within the acceptable range at each vehicle speed.




b.

Inspect tachometer operation

i.

Warm up the engine.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Enter the following menus: Powertrain / Engine / Data List.


v.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm for A25A-FKS:
600 to 700 rpm: Idling (shift lever in P, engine warmed up and A/C off)
for 2GR-FKS:
600 to 700 rpm: Idling (shift lever in N, engine warmed up and A/C off)
for 2AR-FE:
610 to 710 rpm: Idling with warm engine, shift lever in N, A/C off
for A25A-FKS:
Idling (shift lever in P, engine warmed up and A/C off): 650 rpm
for 2GR-FKS:
-
for 2AR-FE:
Idling (engine warmed up and A/C off): 669 rpm
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
Reference
GTS Indication (rpm) Acceptable Range (rpm)
Data in ( ) is for Reference
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)
7000 6700 to 7300

OK:

Tachometer reading is within the acceptable range at each engine speed.




c.

Check LED illumination (LED check)

i.

Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

OK:
Warning or Indicator Light Specified Condition
Brake warning light / red (malfunction) Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.
Slip indicator light
VSC OFF indicator light
ABS warning light
Tire pressure warning light*1
Master warning light
Brake warning light / yellow (minor malfunction)
Brake hold standby indicator light
Brake hold operated indicator light
PCS warning light*2
SRS warning light Warning light comes on for about 6 seconds after turning the ignition switch to ON.
EPS warning light When the ignition switch is turned to ON, warning light (red) illuminates for 2 seconds and then the warning light (yellow) illuminates.
MIL (Check engine warning light) Warning light comes on when the ignition switch is turned to ON.


*1: w/ Tire Pressure Warning System

*2: w/ Forward Recognition Camera