Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › THROTTLE BODY
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0326377 THROTTLE BODY A

2GR-FKS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A405606C01
2.042,0.875 2.281,0.604 2.281,0.604 2.521,0.604 true 2.542,0.51 2.813,0.729 0.271,0.219 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake air surge tank assembly with the protrusion of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Install the throttle body with motor assembly to the intake air surge tank assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



b.

Connect the throttle body with motor assembly connector.


c.
A405604C01
0.948,2.625 0.948,3.094 0.948,3.094 1.135,3.094 true 2.208,2.115 2.406,2.115 2.406,2.115 2.406,2.573 true 1.208,1.26 0.656,1.521 0.656,1.521 0.656,1.729 true 2.104,1.417 2.49,1.417 true 2.521,1.969 2.833,2.125 0.313,0.156 10 false *a 1.281,2.521 1.594,2.677 0.313,0.156 10 false *b 1.938,2.51 2.25,2.667 0.313,0.156 10 false *c 1.146,3.01 1.458,3.167 0.313,0.156 10 false *d 0.698,1.979 1.01,2.135 0.313,0.156 10 false *a 2.031,2.031 2.344,2.188 0.313,0.156 10 false *d 2.104,2.854 2.417,3.01 0.313,0.156 10 false *e 0.604,1.74 0.823,1.927 0.219,0.188 10 true *1 2.51,1.333 2.729,1.521 0.219,0.188 10 true *2
*1 No. 2 Water By-pass Hose
*2 No. 3 Water By-pass Hose
*a Top
*b Left Side of Vehicle
*c Front of Vehicle
*d Paint Mark
*e 90° (Claw of Clip Location)


Connect the No. 2 water by-pass hose and No. 3 water by-pass hose to the throttle body with motor assembly and slide the 2 clips to secure them.

NOTICE:

Make sure to position each clip as shown in the illustration.



Hide 17705 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A405602C01
0.229,2.896 0.229,2.292 true 0.844,2.5 1.031,2.135 1.031,2.135 1.177,2.135 true 2.125,0.667 2.271,0.906 2.271,0.906 2.333,0.625 true 2.052,0.594 1.813,0.594 1.813,0.594 1.813,0.865 true 0.177,2.906 0.49,3.063 0.313,0.156 10 false *a 1.208,2.052 1.521,2.208 0.313,0.156 10 false *b 1.75,0.875 1.969,1.042 0.219,0.167 10 true *c 2.323,0.042 2.635,0.198 0.313,0.156 10 false *d 1.5,0.229 1.813,0.385 0.313,0.156 10 false *d 2.208,0.927 2.521,1.083 0.313,0.156 10 false *e
*a Protrusion
*b Cutout
*c Hose Clamp End
*d 2.0 mm (0.0787 in.)
*e Paint Mark


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

NOTICE:

Make sure that the end of the hose clamp is positioned as shown in the illustration.



c.

Engage the 2 guides.


d.

Engage the 2 air cleaner cap clamps to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


e.
A405599C01
2.25,0.74 2.729,0.74 true 0.844,0.823 0.969,0.542 0.969,0.542 1.115,0.542 true 1.604,1.698 1.604,1.01 true 0.5,0.573 0.5,0.323 0.5,0.323 0.313,0.323 false 2.74,0.656 2.969,0.854 0.229,0.198 10 true *1 1.542,1.719 1.76,1.906 0.219,0.188 10 true *2 0.76,0.198 1.073,0.354 0.313,0.156 10 false *a 0.146,0.24 0.458,0.396 0.313,0.156 10 false *d 0.083,0.906 0.396,1.063 0.313,0.156 10 false *c 1.135,0.479 1.448,0.635 0.313,0.156 10 false *b
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose
*a Top
*b Paint Mark
*c Rear of Vehicle
*d 180° (Claw of Clip Location)


Connect the No. 2 ventilation hose to the air cleaner hose and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



f.

Engage the 2 clamps to connect the No. 1 fuel vapor feed hose to the air cleaner hose.


g.

Connect the vacuum hose to the air cleaner hose.


h.

Engage the 2 wire harness clamps.


i.

Connect the mass air flow meter sub-assembly connector.


Hide 4.ADD ENGINE COOLANT

Hide 6.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

f.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




g.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage %.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage %
50003 372 216

h.

Fully depress the accelerator pedal and check that the value is 60% or higher.


i.

Perform a road test and confirm that there are no abnormalities.