Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2017.09–2019.10
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0326591 TRANSMISSION CONTROL CABLE N

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.ADJUST SHIFT LEVER POSITION

NOTICE:

Before adjusting the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.


HINT:

Whether the transmission control cable assembly is type A or type B can be determined by the shape of the end.

C413146C01
0.615,0.26 0.917,0.458 0.302,0.198 12 false *A 4.042,0.26 4.333,0.479 0.292,0.219 12 false *B
*A Type A *B Type B



a.

for Type A:

i.
C370819

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


ii.
C194520C31
2.271,2.573 2.615,2.573 false 1.948,1.75 2.083,1.531 2.083,1.531 2.188,1.531 false 1.594,0.958 1.781,1.135 0.188,0.177 10 false *c 1.792,1.344 1.979,1.521 0.188,0.177 10 false *c 2.438,0.781 2.625,0.958 0.188,0.177 10 false *d 2.25,1.458 2.51,1.656 0.26,0.198 10 false *a 2.229,2.313 2.417,2.49 0.188,0.177 10 false *d 2.656,2.49 2.958,2.729 0.302,0.24 10 false *b
*a Slider
*b Lock Piece
*c Slide
*d Pull


Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.


iii.
C370858C01
2.094,2.781 2.24,2.552 2.24,2.552 2.365,2.552 false 1.396,2.677 1.292,2.49 1.292,2.49 1.177,2.49 false 0.979,2.375 1.229,2.594 0.25,0.219 10 false *a 2.427,2.448 2.719,2.646 0.292,0.198 10 false *b
*a Lock Piece
*b Adjuster Case


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Check that the lock piece is pulled out.

·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.




iv.
C296262C01
2.229,0.854 2.365,0.563 2.365,0.563 2.5,0.563 false 1.24,3.219 1.375,2.927 1.375,2.927 1.51,2.927 false 1.208,0.667 1.344,0.375 1.344,0.375 1.479,0.375 false 2.24,3.323 2.375,3.031 2.375,3.031 2.51,3.031 false 1.531,0.281 1.813,0.51 0.281,0.229 10 false *a 1,2.76 1.271,3.01 0.271,0.25 10 false *b 2.552,0.469 2.854,0.698 0.302,0.229 10 false *c 1.552,2.833 1.833,3.063 0.281,0.229 10 false *a 2.542,2.938 2.844,3.167 0.302,0.229 10 false *c
*a Lock Piece
*b Push in
*c Adjuster Case


Push the lock piece into the adjuster case.

NOTICE:
·

Check that the park/neutral position switch assembly and shift lever are in N.

·

Securely push in the lock piece until the slider lock is engaged.




v.

After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.



b.

for Type B:

i.
C413140

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


ii.
C413141C01
1.052,2.469 1.229,2.667 0.177,0.198 10 true *a
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


iii.
C400603C09
1.646,1.198 1.844,1.594 1.844,1.594 2,1.594 false 1.313,1.344 1.583,1.594 0.271,0.25 10 false *b 2.042,1.49 2.333,1.708 0.292,0.219 10 false *a
*a Adjuster Case Cover
*b Slide


Slide the adjuster case cover in the direction shown by the arrow.


iv.
C400817C08
1.333,0.583 1.479,0.583 1.479,0.583 1.719,0.948 false 1.375,1.802 1.531,1.802 1.531,1.802 1.688,1.167 true 1.333,2.719 1.479,2.719 1.479,2.719 1.719,3.083 false 1.396,3.99 1.552,3.99 1.552,3.99 1.708,3.354 true 1.854,1.302 2.156,1.542 0.302,0.24 10 false *b 1.167,1.719 1.406,1.927 0.24,0.208 10 false *a 1.198,3.896 1.438,4.115 0.24,0.219 10 false *a 1.125,0.5 1.375,0.74 0.25,0.24 10 false *c 1.125,2.635 1.333,2.844 0.208,0.208 10 false *c
*a Lock Piece
*b Pull Out
*c Adjuster Case


Using a precision screwdriver, pull out the lock piece of the adjuster case.


v.
C377530C01
2.208,3.344 2.938,2.125 2.938,2.125 2.25,1.198 true 1.938,1.833 2.167,2.156 2.167,2.156 2.333,2.156 false 1.938,4.063 2.167,4.385 2.167,4.385 2.333,4.385 false 2.375,2.063 2.677,2.313 0.302,0.25 10 false *a 2.042,0.458 2.333,0.667 0.292,0.208 10 false *b 3,2.042 3.26,2.219 0.26,0.177 10 false *c 2.375,4.302 2.677,4.552 0.302,0.25 10 false *a
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


vi.
C413142C01
0.458,0.25 0.646,0.25 0.646,0.25 0.854,0.521 false 2.26,0.229 2.448,0.229 2.448,0.229 2.615,0.417 false 0.26,0.167 0.49,0.375 0.229,0.208 10 false *a 2.021,0.146 2.25,0.333 0.229,0.188 10 false *a
*a Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:

After installation, check that the outer part of the stopper is as shown in the illustration.



vii.
C413143

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the shift lever is in N.


·

Securely connect the end of the transmission control cable assembly to the transmission floor shift assembly.




viii.
C413144C01
1.74,1.323 2.24,1.74 2.24,1.74 2.396,1.74 true 1.031,0.635 1.188,0.635 1.188,0.635 1.646,1.073 true 1.521,1.479 1.74,1.677 0.219,0.198 10 false *b 2.448,1.667 2.677,1.875 0.229,0.208 10 false *a 0.813,0.552 1.01,0.74 0.198,0.188 10 true *c
*a Lock Piece
*b Push in
*c Adjuster Case


Push in the lock piece of the adjuster case to lock it.


ix.
C413145C01
0.99,1.792 1.115,1.792 1.115,1.792 1.406,1.375 true 1.042,4.271 1.198,4.271 1.198,4.271 1.51,3.813 true 2.156,4.292 2,4.292 2,4.292 1.729,3.729 true 0.792,1.698 1.063,1.917 0.271,0.219 10 false *b 2.219,4.198 2.479,4.406 0.26,0.208 10 false *a 0.865,4.177 1.135,4.396 0.271,0.219 10 false *b
*a Lock Piece
*b Adjuster Case Cover


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the transmission control cable assembly will not be able to lock, and reliable shift operation will not be possible.