Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM D

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


CAUTION:
·
C328184

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328186

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328185

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform this test with the ATF (Automatic Transaxle Fluid) at the normal operating temperature: 50 to 80°C (122 to 176°F)

·

Be careful to prevent the SST hose from contacting the exhaust pipe.

·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the air conditioning off.

·

Do not perform the stall test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.



a.

Measure the line pressure.

i.

Warm up the ATF.


ii.

Lift the vehicle.


iii.

Remove the engine under cover.


iv.
C370669N01
0.885,4.167 1.25,4.271 true 1.292,4.208 1.75,4.406 0.458,0.198 10 false SST 2.781,4.115 3.24,4.313 0.458,0.198 10 false SST

Remove the test plug on the front left side of the transaxle case and install SST.

SST
09993-19015  (09993-00010, 09993-00040)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



vii.

Connect the GTS to the DLC3.


viii.

Start the engine.


ix.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Shift Position.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Shift Position
50004 234 116

x.

Move the shift lever to D, and then use the GTS to perform the Active Test and hold 3rd gear. Measure the line pressure with the engine idling.

Specified Line Pressure:
Condition D Position
Idling 360 to 430 kPa
(3.6 to 4.4 kgf/cm2, 52 to 63 psi)



xi.

Turn the ignition switch off.


xii.
C370671

Disconnect the connector from the wiring harness connector.

HINT:

Disconnect the connector only when performing the D position stall test.



xiii.

Start the engine.


xiv.

Depress the brake pedal firmly with your left foot, move the shift lever to D, depress the accelerator pedal as much as possible with your right foot, and quickly read the line pressure when the engine reaches the stall speed.

Specified Line Pressure:
Condition D Position
Stall test 1000 to 1400 kPa
(10.1 to 14.3 kgf/cm2, 145 to 204 psi)



xv.

Turn the ignition switch off.


xvi.

Connect the connector to the wiring harness connector.


xvii.

Depress the brake pedal firmly with your left foot, move the shift lever to R, and check the line pressure with the engine idling and then depress the accelerator pedal as much as possible with your right foot and quickly read the line pressure when the engine reaches the stall speed.

Specified Line Pressure:
Condition R Position
Idling 670 to 820 kPa
(6.8 to 8.4 kgf/cm2, 97 to 119 psi)
Stall test 1600 to 2100 kPa
(16.3 to 21.5 kgf/cm2, 232 to 305 psi)



xviii.

Remove SST and install the test plug.


xix.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Evaluation
Test Result Possible Cause
Measured values are higher than the specified value in all positions
·

Solenoid (SLT) valve malfunction

·

Regulator valve malfunction


Measured values are lower than the specified value in all positions
·

Solenoid (SLT) valve malfunction

·

Regulator valve malfunction

·

Oil pump malfunction


Pressure is low in D only
·

D position circuit fluid leak

·

No. 1 clutch (C1) malfunction


Pressure is low in R only
·

R position circuit fluid leak

·

No. 2 brake (B2) malfunction

·

No. 3 brake (B3) malfunction