Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM D

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  INITIALIZATION  


RESET TRANSAXLE COMPENSATION CODE


NOTICE:
·

If the following parts have been replaced, initialize the ECM and perform Reset Memory and Perform Road Test to Allow ECM to Learn.

-

Transmission valve body assembly

-

Solenoid (SL3) valve

-

Solenoid (SL4) valve

-

ECM


·

The transaxle compensation code can only be initialized with the GTS.



HINT:

The ECM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, if the automatic transaxle assembly, transmission valve body assembly, solenoid (SL3) valve, solenoid (SL4) valve or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information. The reset procedure is as follows:


a.

Make sure the shift lever is in P or N.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / A/T Code Reset.

Powertrain > Engine and ECT > Utility
Tester Display
A/T Code Reset
50005 234 209

f.

Press "Next" again to proceed.

NOTICE:

After the transaxle compensation code is initialized, perform Reset Memory and Perform Road Test to Allow ECM to Learn.



g.

Press "Exit".



RESET MEMORY


NOTICE:

Reset Memory can be performed only with the GTS.


HINT:

The ECM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, if the automatic transaxle assembly, transmission valve body assembly, solenoid (SL3) valve, solenoid (SL4) valve or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information. The reset procedure is as follows:


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

Powertrain > Engine and ECT > Utility
Tester Display
Reset Memory
50005 234 176

e.

Press "Next".

NOTICE:

After performing Reset Memory, be sure to perform Perform Road Test to Allow ECM to Learn.




PERFORM ROAD TEST TO ALLOW ECM TO LEARN


CAUTION:

Perform the following procedure while strictly observing all traffic laws and speed limits.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Sensor Position
50003 234 12

g.

From a standstill, achieve highest possible speed with the accelerator pedal opened 15% or less. Keep the accelerator pedal opening angle steady while driving the vehicle.

HINT:

Throttle Sensor Position: 15% or less



h.

Repeat the previous step until shift shock no longer occurs.


i.

From a standstill, achieve highest possible speed with the accelerator pedal opened 25% to 35%. Keep the accelerator pedal opening angle steady while driving the vehicle.

HINT:

Throttle Sensor Position: 25 to 35%



j.

Repeat the previous step until shift shock no longer occurs.



PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET


NOTICE:

If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset.

·

The ATF has been replaced.

HINT:

If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.


·

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

With the shift lever in P, turn the ignition switch to ON.

NOTICE:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menu: Powertrain / Engine and ECT / Utility / ATF Thermal Degradation Estimate Reset.

Powertrain > Engine and ECT > Utility
Tester Display
ATF Thermal Degradation Estimate Reset
50005 234 4273

f.

According to the display on the GTS, initialize the estimated thermal degradation value.