Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2757  Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance or Stuck OFF  


SYSTEM DESCRIPTION

The ECM uses signals from the throttle position sensor, air-flow meter, input speed sensor NT, output speed sensor NC and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C315080C01
1.792,1.417 2.125,0.417 2.125,0.417 2.542,0.417 true 1.219,1.646 0.969,2.146 0.969,2.146 0.635,2.146 true 2.521,1.688 2.771,2.188 2.771,2.188 3.104,2.188 true 2.583,0.333 2.896,0.49 0.313,0.156 10 false *a 0.458,2.063 0.771,2.219 0.313,0.156 10 false *b 3.146,2.104 3.458,2.26 0.313,0.156 10 false *c 4.802,0.625 5.115,0.781 0.313,0.156 10 false *d 6.135,2.031 6.448,2.188 0.313,0.156 10 false *e
*a Spool Valve *b Sleeve
*c Solenoid Coil *d Hydraulic Pressure
*e Current - -


The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical malfunctions of the solenoid (SLU) valve, transmission valve body assembly and torque converter clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2757 Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance or Stuck OFF All of the following conditions are met (2-trip detection logic):
·

The engine coolant temperature is 40°C (104°F) or higher.

·

The ATF temperature is -10°C (14°F) or higher.

·

The vehicle is being driven with the shift lever in D.

·

No malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL and SLU) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, electronic throttle or CAN communication system.

·

When the ECM commands lock-up ON, lock-up does not occur.


·

Solenoid (SLU) valve remains open or closed

·

Transmission valve body assembly is blocked

·

Torque converter assembly

·

Automatic transaxle assembly (clutch, brake, gear, etc.)

·

Line pressure is too low


Comes on DTC stored

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the input speed sensor NT, output speed sensor NC, engine speed, engine load, engine temperature, vehicle speed, automatic transaxle fluid temperature and gear selection signal. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) signal to the input speed sensor NT signal and calculates the actual transmission gear by comparing the input speed sensor NT signal to the output speed sensor NC signal. When conditions are appropriate, the ECM requests "lock-up" by applying voltage to the solenoid (SLU) valve. When the solenoid (SLU) valve is turned on, pressure is applied to the lock-up relay valve and locks the torque converter clutch.

If the ECM does not detect lock-up after lock-up has been requested or if it detects lock-up when it is not requested, it interprets this as a malfunction of the solenoid (SLU) valve or in lock-up system performance, illuminates the MIL and stores this DTC.

Example:

If the following conditions are met, the system judges it as a malfunction.

·

There is a difference in rotation (speed) between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.

(Engine speed is at least 70 rpm greater than input turbine speed.)


CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2757.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


ACTIVE TEST


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Lock Up.


g.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Lock Up Operates the solenoid (SLU and SL) valves to control the automatic transaxle lock-up condition ON/OFF Can be used to check the operation of the solenoid (SLU and SL) valves.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 20%

·

Vehicle speed: 60 km/h (37 mph) or more in 6th gear


Powertrain > Engine and ECT > Active Test
Tester Display
Activate the Lock Up
50004 234 115
HINT:

This Active Test can be performed when the vehicle speed is 60 km/h (37 mph) or more.



h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)



C159073E10
4.531,2.188 5.542,1.958 5.542,1.958 5.604,1.958 false 5.125,2.24 5.542,2.583 5.542,2.583 5.604,2.583 false 0.719,2.677 1.646,2.875 0.927,0.198 10 Engine Speed 0.719,1.677 1.906,2.094 1.188,0.417 10 Accelerator Pedal Fully Released 0.719,1.021 1.906,1.438 1.188,0.417 10 Accelerator Pedal Opening Angle 4.99,3.125 5.438,3.323 0.448,0.198 10 Time 5.656,1.865 6.615,2.063 0.958,0.198 10 Lock-up OFF 5.656,2.49 6.615,2.688 0.958,0.198 10 Lock-up ON



PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P2757 is output A
DTC P2757 and other DTCs are output B


HINT:
·

If any DTCs other than DTC P2757 are output, perform the troubleshooting for those DTCs first.

·

If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.





A

2.INSPECT SOLENOID (SLU) VALVE

B

2.INSPECT SOLENOID (SLU) VALVE
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Solenoid (SLU) Valve


Remove the solenoid (SLU) valve.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL


OK:

There is no foreign matter on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY

OK:

The torque converter assembly is normal.


Result:
Proceed to
OK
NG



OK

NG