Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2019.10
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM J

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S and moved toward "-" or "+", it is possible to select different shift ranges (S1 to S6).

Moving the shift lever toward "+" increases the shift range by one, and moving the shift lever toward "-" decreases the shift range by one.

WIRING DIAGRAM

C318220E11
0.198,0.625 1.083,1.354 0.885,0.729 10 false from ECU-IG1 NO. 3 Fuse 1.667,2.646 3.833,3.229 2.167,0.583 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.688,2.49 2.26,2.813 0.573,0.323 10 false K29 2.083,0.49 2.396,0.688 0.313,0.198 10 false IG 2.063,1.854 2.375,2.042 0.313,0.188 10 false E 3.271,0.49 3.583,0.677 0.313,0.188 10 false S 3.021,1.177 3.635,1.375 0.615,0.198 10 false SFTU 3.021,1.854 3.635,2.052 0.615,0.198 10 false SFTD 5.521,0.51 5.833,0.698 0.313,0.188 10 false S 5.521,1.188 6.135,1.385 0.615,0.198 10 false SFTU 5.521,1.875 6.135,2.073 0.615,0.198 10 false SFTD 5.875,2.469 6.188,2.667 0.313,0.198 10 false A22 5.875,2.635 6.458,3.167 0.583,0.531 10 false ECM 1.865,0.49 2.021,0.688 0.156,0.198 10 false 4 1.865,1.854 2.177,2.052 0.313,0.198 10 false 2 3.521,1.844 3.833,2.042 0.313,0.198 10 false 3*2 3.531,1.177 3.844,1.375 0.313,0.198 10 false 1*2 5.26,0.51 5.573,0.708 0.313,0.198 10 false 59 5.271,1.188 5.583,1.385 0.313,0.198 10 false 42 5.26,1.875 5.573,2.073 0.313,0.198 10 false 43 6.25,1.01 6.708,1.208 0.458,0.198 10 false 12 V 6.25,1.688 6.708,1.885 0.458,0.198 10 false 12 V 3.521,0.5 3.833,0.698 0.313,0.198 10 false 5 3.531,1 3.844,1.198 0.313,0.198 10 false 3*1 3.521,1.677 3.833,1.875 0.313,0.198 10 false 1*1 0.167,3.177 1.854,3.375 1.688,0.198 10 false *1: for LHD 0.167,3.438 1.854,3.635 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Sports Mode Selection SW.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport (S) mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

2.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
2.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Sports Shift Up SW and Sports Shift Down SW.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" or "+" shift paddle switch operated

·

OFF: Shift lever not held in "+" and "+" shift paddle switch released


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" or "-" shift paddle switch operated

·

OFF: Shift lever not held in "-" and "-" shift paddle switch released


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 234 134,135

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K29 transmission control switch connector.


b.
C251980C84
1.719,1.708 1.719,1.281 true 2.167,1.844 1.927,1.292 true 2.542,1.708 2.146,1.281 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 1.531,1.74 2.094,1.948 0.563,0.208 10 false SFTU*A 2.146,1.865 2.323,2.031 0.177,0.167 10 false E 2.469,1.729 3.094,1.927 0.625,0.198 10 false SFTD*A 1.531,1.896 2.094,2.104 0.563,0.208 10 false SFTD*B 2.469,1.896 3.094,2.094 0.625,0.198 10 false SFTU*B
*A for LHD
*B for RHD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" (Up shift) Below 1 Ω
Shift lever not held in "+" (Up shift) 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" (Down shift) Below 1 Ω
Shift lever not held in "-" (Down shift) 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" (Up shift) Below 1 Ω
Shift lever not held in "+" (Up shift) 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" (Down shift) Below 1 Ω
Shift lever not held in "-" (Down shift) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.

Disconnect the K29 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Connect the K29 transmission control switch connector.


b.

Disconnect the A22 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-42 (SFTU) - Body ground Shift lever held in "+" (Up shift) Below 1 Ω
Shift lever not held in "+" (Up shift) 10 kΩ or higher
A22-43 (SFTD) - Body ground Shift lever held in "-" (Down shift) Below 1 Ω
Shift lever not held in "-" (Down shift) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

6.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K29 transmission control switch connector.


b.
C277025C47
0.802,1.802 1.219,1.385 true 1.615,1.781 1.479,1.396 true 1.573,1.833 1.885,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
a.

Disconnect the K29 transmission control switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K29-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH (POWER SOURCE))

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the K29 transmission control switch connector.


b.

Disconnect the A22 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-59 (S) - K29-5 (S) Always Below 1 Ω
A22-59 (S) or K29-5 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)