The ECM controls the solenoid (SLU) valve using a predetermined current, and performs lock-up and flex lock-up control.
| *1 | Spool Valve | *2 | Sleeve |
| *3 | Solenoid Coil | - | - |
| *a | Current | *b | Hydraulic Pressure |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P275612 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery | While the vehicle is being driven, a short to +B is detected in the solenoid (SLU) valve circuit for 1 second (1-trip detection logic). | ·
Solenoid (SLU) valve ·
Transmission wire ·
Harness and connector ·
ECM |
Comes on | DTC stored | SAE Code:
P2763 |
When a short to +B in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for 2 minutes or more.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine.
Perform the Lock-up Function inspection in Road Test.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P275612.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Disconnect the C59 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C59-12 (SLU+) or C59-11 (SLU-) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
Disconnect the C93 transmission wire connector.
Disconnect the C59 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C93-5 (SLU+) or C59-12 (SLU+) - Other terminals | Always | 10 kΩ or higher |
| C93-4 (SLU-) or C59-11 (SLU-) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Solenoid (SLU) Valve) |
Remove the solenoid (SLU) valve.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Solenoid (SLU) valve connector terminal 1 - terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
Valve moves and makes operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG