Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0322781 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P061512  Starter Relay Circuit Short to Battery  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 10.5 V or more.

·

The vehicle speed is 20 km/h (12 mph) or more.

·

The engine speed is more than 1000 rpm.

·

The starter signal is ON for 20 seconds or more.


·

Park/neutral position switch assembly

·

Starter relay circuit

·

Cranking holding function circuit

·

Harness and connector

·

ECM

·

Certification ECU (Smart key ECU assembly)


Comes on DTC stored SAE Code:
P0617

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Drive the vehicle for 20 seconds or more with the following conditions met:

-

Engine speed is 1000 rpm or more.

-

Vehicle speed is 20 km/h (12 mph) or more.


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P061512.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C380274E02
0.146,1.688 1.667,2.167 1.521,0.479 10 false Certification ECU (Smart Key ECU Assembly) 3.167,1.552 5.604,1.813 2.438,0.26 10 false Park/Neutral Position Switch Assembly 3.677,3.906 4.854,4.167 1.177,0.26 10 false Starter Assembly 0.521,4.906 1.594,5.104 1.073,0.198 10 false Battery 0.375,3.083 1.448,3.281 1.073,0.198 10 false FL MAIN 0.948,2.656 2.021,2.854 1.073,0.198 10 false ST NO. 1 2.552,3.167 3.625,3.365 1.073,0.198 10 false ST 6.417,2.646 6.927,2.844 0.51,0.198 10 false ECM 6.125,1.865 6.635,2.063 0.51,0.198 10 false STA 5.792,1.75 6.302,1.948 0.51,0.198 10 false 43 5.75,1.979 6.26,2.177 0.51,0.198 10 false A23 5.75,0.75 6.26,0.948 0.51,0.198 10 false C96 5.76,0.531 6.271,0.729 0.51,0.198 10 false 106 6.125,0.625 6.635,0.823 0.51,0.198 10 false NSW 6.698,0.448 7.073,0.677 0.375,0.229 10 false 12 V 4.729,1.104 5.24,1.302 0.51,0.198 10 false 4 4.5,1.104 5.01,1.302 0.51,0.198 10 false B 3.875,1.104 4.385,1.302 0.51,0.198 10 false L 3.646,1.104 4.156,1.302 0.51,0.198 10 false 9 3.177,1.396 3.688,1.594 0.51,0.198 10 false C55 1.417,0.625 1.927,0.823 0.51,0.198 10 false 9 1.427,1.104 1.938,1.302 0.51,0.198 10 false 20 1.021,1.229 1.531,1.427 0.51,0.198 10 false STA 0.938,0.74 1.448,0.938 0.51,0.198 10 false STAR 0.146,1.531 0.656,1.729 0.51,0.198 10 false A13 2.188,2.396 2.698,2.594 0.51,0.198 10 false 5 2.969,2.396 3.479,2.594 0.51,0.198 10 false 3 2.969,2.781 3.479,2.979 0.51,0.198 10 false 2 2.188,2.781 2.698,2.979 0.51,0.198 10 false 1 4.302,3.146 4.813,3.344 0.51,0.198 10 false C61 4.5,2.927 5.01,3.125 0.51,0.198 10 false 1 3.344,3.427 3.854,3.625 0.51,0.198 10 false 1 3.271,3.646 3.781,3.844 0.51,0.198 10 false C74

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / Starter SW.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Powertrain > Transmission > Data List
Tester Display
Starter SW
50003 373 11

e.

Read the Data List according to the display on the GTS.

OK:
Condition Starter SW
Engine switch on (IG) OFF



f.

Read the Data List according to the display on the GTS while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.

OK:
Condition Starter SW
Driving at 20 km/h (12 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the engine switch on (IG), the GTS connected and Data List item "Starter SW" selected.


Result:
Proceed to
OK
NG


HINT:

If the starter assembly operates continuously when the engine switch is turned on (IG), proceed to the next step without reading the Data List item "Starter SW".



OK

NG

2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Transmission / Data List / Starter SW.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Powertrain > Transmission > Data List
Tester Display
Starter SW
50003 373 11

b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Read the Data List according to the display on the GTS.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON. A
The Data List item "Starter SW" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
HINT:

The purpose of this step is to check for ST relay terminal voltage under abnormal conditions.


a.
C375873C01
1.583,0.229 1.896,0.385 0.313,0.156 10 false *1 0.354,1.302 0.667,1.458 0.313,0.156 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay Holder


Remove the ST relay from the engine room relay block and junction block assembly.


b.

Turn the engine switch on (IG).


c.

Measure the voltage between ST relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the engine switch on (IG) and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the engine switch on (IG), one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or park/neutral position switch assembly.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
a.
C375873C01
1.583,0.229 1.896,0.385 0.313,0.156 10 false *1 0.354,1.302 0.667,1.458 0.313,0.156 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay Holder


Disconnect the C55 park/neutral position switch assembly connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
a.
C375873C01
1.583,0.229 1.896,0.385 0.313,0.156 10 false *1 0.354,1.302 0.667,1.458 0.313,0.156 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay Holder


Disconnect the A23 ECM connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)

B

7.REPLACE ECM
6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)
a.

Disconnect the A23 ECM connector.


b.

Disconnect the C55 park/neutral position switch assembly connector.


c.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


d.

Remove the ST relay from the engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-43 (STA), C55-9 (L), A13-20 (STA) or 2 (ST relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK SMART ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT