Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0322781 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P07957F  Pressure Control Solenoid "C" Actuator Stuck Off  


DESCRIPTION

Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected.

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves, transmission valve body assembly and automatic transaxle assembly (clutch, brake, gear, etc.).

HINT:
Actual gear when solenoid (SL3) valve malfunction occurs (without fail-safe control):
ECM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th

*: Neutral

Actual gear during SL3 stuck ON malfunction 3rd 3rd 3rd 3rd 3rd to 5th 7th 7th 7th
Actual gear during SL3 stuck OFF malfunction 1st 2nd N* 4th 5th 6th N* 8th


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07957F Pressure Control Solenoid "C" Actuator Stuck Off All of the following conditions are met (2-trip detection logic):
·

Engine coolant temperature is 40°C (104°F) or higher.

·

ATF temperature is -10°C (14°F) or higher.

·

The vehicle is being driven with the shift lever in D.

·

No malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuits, electronic throttle or CAN communication system.

·

Any of the following conditions are met:

-

When the ECM commands the transaxle to shift to 1st, 2nd, 4th or 5th gear, the actual gear changes to 3rd gear for 0.8 seconds or more.

-

When the ECM commands the transaxle to shift to 6th or 8th gear, the actual gear changes to 7th gear for 0.8 seconds or more.

-

When the ECM commands the transaxle to shift to 3rd or 7th gear, the engine overruns (neutral status) for 0.5 seconds or more.



·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SL) valve

·

Solenoid (SLU) valve

·

Solenoid (SLT) valve

·

Transmission valve body assembly

·

Torque converter assembly

·

Automatic transaxle assembly (clutch, brake, gear, etc.)


Comes on DTC stored SAE Code:
P0796

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnostic Condition Engine coolant temperature is 40°C (104°F) or higher. ○ ○ ○ ○
ATF temperature is -10°C (14°F) or higher. ○ ○ ○ ○
The vehicle is being driven with the shift lever in D. ○ ○ ○ ○
No malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuits, electronic throttle or CAN communication system. ○ ○ ○ ○
Malfunction Condition When the ECM commands the transaxle to shift to 1st gear, the actual gear changes to 3rd gear. ○ - - -
When the ECM commands the transaxle to shift to 2nd gear, the actual gear changes to 3rd gear. - ○ - -
When the ECM commands the transaxle to shift to 4th gear, the actual gear changes to 3rd gear. - - ○ -
When the ECM commands the transaxle to shift to 5th gear, the actual gear changes to 3rd to 5th gear. - - - ○
Duration 0.8 seconds or more 0.8 seconds or more 0.8 seconds or more 0.8 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnostic Condition Engine coolant temperature is 40°C (104°F) or higher. ○ ○ ○ ○
ATF temperature is -10°C (14°F) or higher. ○ ○ ○ ○
The vehicle is being driven with the shift lever in D. ○ ○ ○ ○
No malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuits, electronic throttle or CAN communication system. ○ ○ ○ ○
Malfunction Condition When the ECM commands the transaxle to shift to 6th gear, the actual gear changes to 7th gear. ○ - - -
When the ECM commands the transaxle to shift to 8th gear, the actual gear changes to 7th gear. - ○ - -
When the ECM commands the transaxle to shift to 3rd gear, the engine overruns (neutral status). - - ○ -
When the ECM commands the transaxle to shift to 7th gear, the engine overruns (neutral status). - - - ○
Duration 0.8 seconds or more 0.8 seconds or more 0.5 seconds or more 0.5 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

The ECM commands gear shifts by turning the solenoid valves on and off. According to the input shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P07957F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P07957F)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTC P07957F and DTC P07457F, P07407E, P07757F, P08BA7F, P27137F, P28077F and/or P28167F are output A
Only DTC P07957F is output B
DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are also output C


HINT:
·

If any DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.

·

If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.





A

2.CLEAR DTC AND PERFORM STALL SPEED TEST

B

3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE

C

2.CLEAR DTC AND PERFORM STALL SPEED TEST
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
HINT:

Write down the currently output DTCs before clearing them.



b.

Perform the stall speed test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>MECHANICAL SYSTEM TESTS

Result:
Test Condition Proceed to
Stall speed test can be performed A
Stall speed test cannot be performed B




A

3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE

B

5.INSPECT SOLENOID (SLT) VALVE
3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) Valves)


Remove the solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) valves.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL1) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL2) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL3) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL4) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL5) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL6) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL) VALVE

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) OR (SL6) VALVE

4.INSPECT SOLENOID (SL) VALVE
a.
C361133C03
0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 2.583,0.24 3.042,0.438 0.458,0.198 10 false (+) 1.594,0.26 2.052,0.458 0.458,0.198 10 false (-)
*1 Solenoid (SL) Valve


Remove the solenoid (SL) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

5.INSPECT SOLENOID (SLT) VALVE

NG

5.INSPECT SOLENOID (SLT) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLT) Valve)


Remove the solenoid (SLT) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLT) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Inspect the transmission valve body assembly.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.



Result:
Proceed to
OK
NG



OK

7.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

7.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Inspect the torque converter assembly.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly is normal.



Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

8.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY
a.

Repair or replace the automatic transaxle assembly.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT