Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Panoramic Moon Roof) › 2017.09–2018.04
RM33A0E _59 Vehicle Exterior _065391 SLIDING ROOF / CONVERTIBLE _0326620 SLIDING ROOF HOUSING(for Panoramic Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Panoramic Moon Roof)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Sliding roof ECU (sliding roof drive gear)

·

Slide roof housing panel

·

Slide roof rail sub-assembly

·

Sliding roof glass sub-assembly


Initialize panoramic moon roof system (for Sliding Roof)
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter linked function

·

Sliding roof open warning function


(Click here)
·

Roof sunshade ECU (sliding roof drive gear assembly)

·

Sunshade trim sub-assembly

·

Slide roof rail sub-assembly


Initialize panoramic moon roof system (for Roof Sunshade)
·

Auto operation function

·

Jam protection function

·

Key-off operation function


Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 63218M 1.REMOVE NO. 3 SLIDING ROOF SIDE GARNISH LH

a.

Move the sunshade trim sub-assembly to the fully opened position.


b.
B480209

Remove the No. 3 sliding roof side garnish LH.


Hide 63217K 2.REMOVE NO. 3 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63218M 3.REMOVE NO. 4 SLIDING ROOF SIDE GARNISH LH

a.
B480210

Remove the No. 4 sliding roof side garnish LH.


Hide 63217K 4.REMOVE NO. 4 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63218M 5.REMOVE NO. 2 SLIDING ROOF SIDE GARNISH LH

a.

Move the sliding roof glass sub-assembly to the fully tilted up position.


b.
B480211

Remove the No. 2 sliding roof side garnish LH.


Hide 63217K 6.REMOVE NO. 2 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63201G 7.REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Move the sliding roof glass sub-assembly to the fully closed position.


b.

Using a T25 "TORX" socket wrench, remove the 6 screws and sliding roof glass sub-assembly.

B480185

NOTICE:

To prevent the sliding roof glass sub-assembly and sliding roof drive gear assembly from becoming misaligned, move the sliding roof glass sub-assembly to the fully closed position before removing.



Hide 62180A 8.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 9.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63249E 10.DISCONNECT SLIDING ROOF DRAIN HOSE

HINT:

Use the same procedure for all of the sliding roof drain hoses.


a.
B480186

for Clamp Type:

i.

Disengage the claw and disconnect the sliding roof drain hose.



b.
B480187

for Clip Type:

i.

Expand the clip and disconnect the sliding roof drain hose.



Hide 63242A 11.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH

a.
B480188C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and front sliding roof housing mounting bracket LH.


Hide 63241A 12.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 63244C 13.REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH

a.
B480189C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and center sliding roof housing mounting bracket LH.


Hide 63243C 14.REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 63246D 15.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH

a.
B480190C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and 2 rear sliding roof housing mounting brackets LH.


Hide 63245D 16.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.


Hide 17.REMOVE SLIDING ROOF HOUSING ASSEMBLY

a.

Remove the 20 nuts.

B480191


b.

Disengage the 2 guides and remove the sliding roof housing assembly.