81175
1.INSPECT HEADLIGHT UNIT ASSEMBLY LH
| *1 | Headlight Unit Assembly LH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to Headlight Unit LH) |
| *c | Component without harness connected
(to Headlight Leveling Motor LH) |
*d | Component without harness connected
(to Headlight Lens LH) |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - D-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - D-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - D-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - C-5 | Always | Below 1 Ω |
| B-5 (LOLED1) - C-6 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (HI+) - C-10 | Always | Below 1 Ω |
| B-1 (HI-) - C-4 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the headlight fan circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - C-12 | Always | Below 1 Ω |
| B-15 (FANP) - C-11 | Always | Below 1 Ω |
| B-14 (FANG) - C-4 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - E-7 | Always | Below 1 Ω |
| B-11 (DRL-) - E-8 | Always | Below 1 Ω |
| B-16 (PWM1) - E-6 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the turn signal light circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - E-4 | Always | Below 1 Ω |
| B-13 (TURN-) - E-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
81171A
2.INSPECT HEADLIGHT UNIT LH
| *a | Component without harness connected
(Headlight Unit LH) |
Apply battery voltage to the headlight unit LH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 4 |
Operates normally |
If the result is not as specified, replace the headlight unit LH.
81171B
3.INSPECT HEADLIGHT LENS LH
| *a | Component without harness connected
(Headlight Lens LH) |
Apply battery voltage to the headlight lens LH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 2 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the headlight lens LH.
81135
4.INSPECT HEADLIGHT UNIT ASSEMBLY RH
| *1 | Headlight Unit Assembly RH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to Headlight Unit RH) |
| *c | Component without harness connected
(to Headlight Leveling Motor RH) |
*d | Component without harness connected
(to Headlight Lens RH) |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - D-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - D-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - D-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - C-5 | Always | Below 1 Ω |
| B-5 (LOLED1) - C-6 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (HI+) - C-10 | Always | Below 1 Ω |
| B-1 (HI-) - C-4 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the headlight fan circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - C-12 | Always | Below 1 Ω |
| B-15 (FANP) - C-11 | Always | Below 1 Ω |
| B-14 (FANG) - C-4 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (DRL+) - E-7 | Always | Below 1 Ω |
| B-11 (DRL-) - E-8 | Always | Below 1 Ω |
| B-16 (PWM1) - E-6 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the turn signal light circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - E-4 | Always | Below 1 Ω |
| B-13 (TURN-) - E-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
81131A
5.INSPECT HEADLIGHT UNIT RH
| *a | Component without harness connected
(Headlight Unit RH) |
Apply battery voltage to the headlight unit RH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 4 |
Operates normally |
If the result is not as specified, replace the headlight unit RH.
81131B
6.INSPECT HEADLIGHT LENS RH
| *a | Component without harness connected
(Headlight Lens RH) |
Apply battery voltage to the headlight lens RH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 2 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the headlight lens RH.