Home › Vehicle Exterior › LIGHTING (EXT) › HEIGHT CONTROL SENSOR
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0327016 HEIGHT CONTROL SENSOR G

LIGHTING (EXT)  HEIGHT CONTROL SENSOR  INSPECTION  


PROCEDURE

Hide 89408C 1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

a.

Preparation for check

i.

Confirm the standard, high and low positions of the link that will be used in the following inspection.

·

The standard position is 58° from the maximum link angle (high) and 51° from the maximum link angle (low).

·

The high position (+45°) is 13° from the maximum link angle (high).

·

The low position (-45°) is 6° from the maximum link angle (low).


E345188C02
2.188,1.052 2.5,1.208 0.313,0.156 10 false *a 4.24,0.115 4.552,0.271 0.313,0.156 10 false *b 2.198,3.469 2.51,3.625 0.313,0.156 10 false *c 3.146,0.479 3.458,0.635 0.313,0.156 10 false *d 2.063,2.146 2.375,2.302 0.313,0.156 10 false *e 3.406,0.885 3.719,1.042 0.313,0.156 10 false *f 2.573,2.031 2.885,2.188 0.313,0.156 10 false *g 4.188,0.708 4.5,0.865 0.313,0.156 10 false *h 2.719,3.063 3.031,3.219 0.313,0.156 10 false *i
*a Standard Position *b Maximum Link Angle (Low)
*c Maximum Link Angle (High) *d 51°
*e 58° *f -45°
*g +45° *h 6°
*i 13° - -



ii.

Connect 3 dry cell batteries (1.5 V) in series.

NOTICE:

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.



iii.

Connect a positive (+) lead from the batteries to terminal 3 (SHB) and a negative (-) lead to terminal 1 (SHG).

E345189C07
5.021,2.5 5.406,2.01 false 5.521,2.521 5.604,1.99 false 6.01,2.521 5.823,2 false 4.833,1.281 5.146,1.438 0.313,0.156 10 false *a 2.792,0.156 3.104,0.313 0.313,0.156 10 false *b 1.042,1.146 1.354,1.302 0.313,0.156 10 false *c 0.844,3.104 1.156,3.26 0.313,0.156 10 false *d 1.948,0.635 2.26,0.792 0.313,0.156 10 false *e 0.948,2.052 1.26,2.208 0.313,0.156 10 false *f 4.823,2.531 5.281,2.729 0.458,0.198 10 false SHB 5.344,2.542 5.802,2.74 0.458,0.198 10 false SHRR 5.927,2.542 6.385,2.74 0.458,0.198 10 false SHG
*a Component without harness connected
(Rear Height Control Sensor Sub-assembly LH)
*b Low
*c Standard Position *d High
*e -45° *f +45°



iv.

Measure the voltage between terminals 2 (SHRR) and 1 (SHG) while slowly moving the link up and down.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (SHRR) - 1 (SHG) +45° (High) 4.5 V
2 (SHRR) - 1 (SHG) 0° (Standard position) 2.5 V
2 (SHRR) - 1 (SHG) -45° (Low) 0.5 V


If the result is not as specified, replace the rear height control sensor sub-assembly LH.