Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065380 LIGHTING (INT) _0327154 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E352878E10
1.49,2.156 3.323,2.354 1.833,0.198 10 false Engine Switch 4.75,2.156 6.552,2.521 1.802,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.479,1.99 1.813,2.177 0.333,0.188 10 false K63 4.74,2 5.063,2.177 0.323,0.177 10 false K62 5.083,1.323 5.5,1.521 0.417,0.198 10 false AGND 5.073,0.688 5.49,0.885 0.417,0.198 10 false SWIL 4.823,1.323 5.094,1.5 0.271,0.177 10 false 11 4.802,0.698 5.073,0.875 0.271,0.177 10 false 10 5.885,0.646 6.156,0.823 0.271,0.177 10 false +B 3.75,0.688 4.021,0.865 0.271,0.177 10 false 9 3.771,1.302 4.042,1.479 0.271,0.177 10 false 6 3.292,0.688 3.667,0.865 0.375,0.177 10 false SWIL 3.24,1.313 3.656,1.51 0.417,0.198 10 false AGND

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.*

*: w/ Smart Entry and Start System



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch illumination OFF or ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K63-9 (SWIL) - K62-10 (SWIL) Always Below 1 Ω
K63-6 (AGND) - K62-11 (AGND) Always Below 1 Ω
K63-9 (SWIL) or K62-10 (SWIL) - Body ground Always 10 kΩ or higher
K63-6 (AGND) or K62-11 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR