Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2018.04
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation. This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc. The DTC is cleared when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU (brake actuator assembly) turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.*

4.

The +BS terminal voltage is less than 6.7 V and the skid control ECU (brake actuator assembly) judges that power supply voltage is abnormal for 0.06 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



*: The skid control ECU (brake actuator assembly) monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU (brake actuator assembly) determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

DTC Detection Conditions: C1241
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The vehicle speed is 6 km/h (4 mph) or more. ○ ○ - -
The vehicle speed is 15 km/h (9 mph) or more and the +BS terminal voltage is 9.6 V or more. - - ○ -
The +BS terminal voltage is less than 6.7 V. - - - ○
Malfunction Status The +BS terminal voltage (soft low voltage) is less than 9.6 V. ○ - - -
The +BS terminal voltage (hard low voltage) is less than 6.9 V. - ○ - -
The skid control ECU (brake actuator assembly) turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.* - - ○ -
The skid control ECU (brake actuator assembly) judges that power supply voltage is abnormal. - - - ○
Detection Time 1 second or more 1 second or more - 0.06 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip

*: The skid control ECU (brake actuator assembly) monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU (brake actuator assembly) determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C378289E03
6.427,0.833 6.74,1.031 0.313,0.198 10 false IC 6.417,1.823 6.729,2.021 0.313,0.198 10 false IC 1.813,1.844 2.938,2.125 1.125,0.281 10 false from Battery 1.271,0.844 2.844,1.177 1.573,0.333 10 false from IG1 NO. 1 Relay 3.406,2.031 4.531,2.313 1.125,0.281 10 false ABS NO. 2 3.281,1.021 4.406,1.292 1.125,0.271 10 false ECU-IG1 NO. 2 4.938,1.74 5.25,1.938 0.313,0.198 10 false 30 4.938,0.75 5.25,0.948 0.313,0.198 10 false 36 4.938,3.063 5.25,3.26 0.313,0.198 10 false 46 5.167,1.969 5.583,2.208 0.417,0.24 10 false +BS 5.188,0.969 5.604,1.208 0.417,0.24 10 false IG1 5.177,3.271 5.594,3.51 0.417,0.24 10 false GND1 4.26,3.979 4.719,4.177 0.458,0.198 10 false A34 4.25,4.146 7.156,4.51 2.906,0.365 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C360727C69
0.229,0.302 0.635,0.563 0.406,0.26 1.49,0.927 1.771,0.417 true 0.927,1.792 0.677,1.063 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.302,0.344 0.635,0.542 0.333,0.198 10 false A34 1.698,0.25 2.333,0.438 0.635,0.188 10 false IG1 0.833,1.823 1.563,2.021 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-30 (+BS) - Body ground Always 11 to 14 V
A34-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C70
0.302,0.302 0.74,0.552 0.438,0.25 2.396,0.344 2.74,0.99 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.385,0.333 0.698,0.531 0.313,0.198 10 false A34 2.219,0.177 2.719,0.385 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1241 is not output A
C1241 is output B



A

B