Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever an ABS DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (ECU or sensor) state as Freeze Frame Data.


b.

The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

HINT:
·

If the vehicle is stopped or driven at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number.

·

Freeze Frame Data at the time the ABS operates:

The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.

When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.

·

Freeze Frame Data at the time a DTC is detected:

When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.





CHECK FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

f.

Select a DTC to display its Freeze Frame Data.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 msec, Max.: 510 msec - -
Number of IG ON Number of times ignition switch turned to ON after Freeze Frame Data stored 0 to 31 - -
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Gear Position Gear position information P/N, R, 1st-10th, Fail or Not R Actual gear position -
Shift Lever Position Shift lever position information P/N, R, D/M, 1st-6th/B or Fail Actual shift lever position -
Operated System Operated system status Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC, SCB, Sys Actual operated system Non: No operation is activated.
ABS: ABS is activated.
VSC: VSC is activated.
TRC: TRC is activated.
BA: BA is activated.
HAB: HAB is activated.
Fail: Fail-safe mode is activated.
PBA: PBA is activated.
PB: PB is activated.
HA-CTRL: Hill-start assist control is activated.
TSC: Trailer sway control activated*
SCB: Secondary collision brake is activated.
Sys: System prohibit is activated.
HINT:

*: Not supported


Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed
M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s, Max.: 225 MPa/s Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G Min.: - 25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle speed grade Min.: -25.10 m/s2, Max.: 24.90 m/s2 Vehicle stopped: 0 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Real Engine Torque Actual engine torque Min.: -1024 Nm, Max.: 1023 Nm - -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 127.5% The accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor Steering angle sensor Min.: - 3276.8°, Max.: 3276.7° Left turn: Increase
Right turn: Decrease
-
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode, VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode
-
Brake Hold Ready Brake hold control permission status OFF or ON ON: Brake hold control permitted
OFF: Brake hold control not permitted
-
Brake Hold Control Mode Brake hold control mode OFF, ON, Release or EPB OFF: Brake hold control is not operating
ON: Brake hold control is operating
Release: Brake hold control is released
EPB: Parking brake is engaged during brake hold control
HINT:

EPB stands for electric parking brake.




CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105