Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1249  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied. DTCs may be stored if either of the following occurs:

·

Stop light switch assembly stuck on malfunction.

·

The accelerator and brake pedals are depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1249 Open in Stop Light Switch Circuit The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch assembly is on for 60 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C376902E04
1.854,0.063 3.24,0.375 1.385,0.313 10 false from Battery 1.073,1.438 1.688,1.635 0.615,0.198 10 false STOP 1.969,3.115 2.583,3.313 0.615,0.198 10 false GND 3.396,3.115 4.01,3.313 0.615,0.198 10 false OUT 3.396,2.021 4.01,2.219 0.615,0.198 10 false ACC 3.573,1.021 4.188,1.219 0.615,0.198 10 false L 5.521,1.021 6.135,1.219 0.615,0.198 10 false STP 5.51,2.021 6.125,2.219 0.615,0.198 10 false STPO 5.521,3.104 6.135,3.302 0.615,0.198 10 false STP2 5.417,3.917 6.031,4.115 0.615,0.198 10 false A34 5.406,4.083 6.948,4.521 1.542,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 4.135,3.99 4.948,4.365 0.813,0.375 10 false to Stop Light Circuit 2,3.542 2.615,3.74 0.615,0.198 10 false A37 2,3.688 4.031,4.042 2.031,0.354 10 false Stop Light Switch Assembly 0.615,4.365 2.229,4.604 1.615,0.24 10 false : Open Detection Area 1.802,1.177 2.021,1.406 0.219,0.229 10 false 7 1.802,2.927 2.021,3.156 0.219,0.229 10 false 2 3.75,0.823 3.969,1.052 0.219,0.229 10 false 3 3.75,1.823 3.969,2.052 0.219,0.229 10 false 4 3.75,2.917 3.969,3.146 0.219,0.229 10 false 1 5.302,0.833 5.573,1.104 0.271,0.271 10 false 42 5.302,1.823 5.521,2.052 0.219,0.229 10 false 10 5.302,2.927 5.573,3.198 0.271,0.271 10 false 44 1.979,1.375 2.135,1.573 0.156,0.198 10 false B 5.521,3.49 6.135,3.688 0.615,0.198 10 false GND1 5.302,3.385 5.573,3.656 0.271,0.271 10 false 46 1.448,1.198 1.667,1.427 0.219,0.229 10 false 2 0.99,1.198 1.208,1.427 0.219,0.229 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (BS1 VOLTAGE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
Chassis > ABS/VSC/TRC > Data List
Tester Display
BS1 Voltage Value
50003 105 273

d.

Take a note of the +BS voltage value.

HINT:

The noted +BS voltage value is used in a later step.



Result:
Proceed to
NEXT



NEXT

2.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
2.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
a.

Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

OK:

The pedals were not depressed simultaneously.


HINT:

The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

7.CLEAR DTC
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
5.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1249 is not output A
C1249 is output B



A

B

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.CLEAR DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

Result:
Proceed to
NEXT



NEXT

END