Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2018.04
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and skid control ECU (brake actuator assembly).

·

The ABS is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C367814E07
0.802,0.615 1.417,0.813 0.615,0.198 10 false CANL 0.792,1.219 1.406,1.417 0.615,0.198 10 false CANH 0.188,3.99 0.802,4.188 0.615,0.198 10 false K21 0.177,4.156 1.344,4.573 1.167,0.417 10 false Combination Meter Assembly 1.844,3.542 4.177,3.802 2.333,0.26 10 false : CAN Communication Line 1.323,0.479 1.552,0.667 0.229,0.188 10 false 31 1.323,1.083 1.552,1.271 0.229,0.188 10 false 32 5.781,0.5 6.01,0.688 0.229,0.188 10 false 19 5.844,1.073 6.073,1.26 0.229,0.188 10 false 5 5.781,1.625 6.01,1.813 0.229,0.188 10 false 30 5.771,2.313 6,2.5 0.229,0.188 10 false 36 5.781,3.177 6.01,3.365 0.229,0.188 10 false 46 6.042,0.625 6.656,0.823 0.615,0.198 10 false CANL 6.042,1.219 6.656,1.417 0.615,0.198 10 false CANH 6.031,1.708 6.646,1.906 0.615,0.198 10 false +BS 6.042,2.365 6.385,2.583 0.344,0.219 10 false IG1 6.042,3.24 6.5,3.458 0.458,0.219 10 false GND1 5.49,3.969 5.948,4.188 0.458,0.219 10 false A34 5.479,4.135 7.031,4.625 1.552,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 4.354,2.604 5.708,2.927 1.354,0.323 10 false ECU-IG1 NO. 2 4.448,1.917 5.229,2.156 0.781,0.24 10 false ABS NO. 2 2.833,1.708 3.75,1.958 0.917,0.25 10 false from Battery 2.281,2.354 3.823,2.604 1.542,0.25 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C360727C69
0.229,0.302 0.635,0.563 0.406,0.26 1.49,0.927 1.771,0.417 true 0.927,1.792 0.677,1.063 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.302,0.344 0.635,0.542 0.333,0.198 10 false A34 1.698,0.25 2.333,0.438 0.635,0.188 10 false IG1 0.833,1.823 1.563,2.021 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-30 (+BS) - Body ground Always 11 to 14 V
A34-36 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C70
0.302,0.302 0.74,0.552 0.438,0.25 2.396,0.344 2.74,0.99 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.385,0.333 0.698,0.531 0.313,0.198 10 false A34 2.219,0.177 2.719,0.385 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51

c.

Check the GTS display condition of the ABS warning light.


Result:
Result Proceed to
The value of ABS Warning Light is ON A
The value of ABS Warning Light is OFF B



A

B