Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2018.04
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM

WIRING DIAGRAM

E361054E05
2.854,3.375 6.521,3.573 3.667,0.198 10 false : CAN Communication Line 0.375,4.115 1.573,4.604 1.198,0.49 10 false Combination Meter Assembly 5.594,4.063 7.156,4.479 1.563,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.958,1.01 6.573,1.208 0.615,0.198 10 false CANL 0.927,1.021 1.542,1.219 0.615,0.198 10 false CANL 0.906,1.927 1.521,2.125 0.615,0.198 10 false CANH 5.958,1.948 6.573,2.146 0.615,0.198 10 false CANH 0.375,3.938 0.99,4.135 0.615,0.198 10 false K21 5.594,3.885 6.208,4.083 0.615,0.198 10 false A34 1.427,0.823 1.646,1.042 0.219,0.219 10 false 31 1.448,1.76 1.667,1.979 0.219,0.219 10 false 32 5.677,0.823 5.896,1.042 0.219,0.219 10 false 19 5.74,1.74 5.958,1.958 0.219,0.219 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (SLIP INDICATOR LIGHT)

NG

4.READ VALUE USING GTS (SLIP INDICATOR LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Slip Indicator Light Slip indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Slip Indicator Light
50003 105 53

d.

Check the GTS display condition of the slip indicator light.


Result:
Result Proceed to
The value of Slip Indicator Light is ON A
The value of Slip Indicator Light is OFF B



A

B