Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C379806E05
0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.896,1.74 1.51,1.938 0.615,0.198 10 false CANH 0.104,3.917 0.719,4.115 0.615,0.198 10 false K21 0.104,4.094 2.031,4.375 1.927,0.281 10 false Combination Meter Assembly 1.396,0.75 1.708,0.948 0.313,0.198 10 false 31 1.385,1.552 1.698,1.75 0.313,0.198 10 false 32 5.083,0.75 5.396,0.948 0.313,0.198 10 false 19 5.156,1.563 5.469,1.76 0.313,0.198 10 false 5 4.729,2.625 5.042,2.823 0.313,0.198 10 false 5 4.51,2.823 4.823,3.021 0.313,0.198 10 false + 3.833,2.833 4.146,3.031 0.313,0.198 10 false E 3.615,2.615 3.927,2.813 0.313,0.198 10 false 2 5.146,2.625 5.458,2.823 0.313,0.198 10 false 6 5.375,0.927 5.99,1.125 0.615,0.198 10 false CANL 5.375,1.74 5.99,1.938 0.615,0.198 10 false CANH 5.365,2.844 5.979,3.042 0.615,0.198 10 false CSW 3.708,3.115 4.323,3.313 0.615,0.198 10 false K39 3.698,3.271 5.458,3.573 1.76,0.302 10 false VSC OFF Switch 2.948,4.333 5.042,4.594 2.094,0.26 10 false : CAN Communication Line 6.49,2.74 7.104,2.938 0.615,0.198 10 false IC 5.302,3.948 5.917,4.146 0.615,0.198 10 false A34 5.302,4.104 6.854,4.49 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

b.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display ("Traction Control Turned Off") VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the VSC OFF switch TRC OFF Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRACTION CONTROL TURNED OFF) AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRACTION CONTROL TURNED OFF) AND VSC OFF INDICATOR LIGHT)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (Traction Control Turned Off) Display OFF/ON Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light OFF/ON Observe combination meter assembly
Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check that "Traction Control Turned Off" on the multi-information display and the VSC OFF indicator light on the combination meter assembly turn on or off in accordance with the operation of the GTS.

OK:

"Traction Control Turned Off" on the multi-information display and the VSC OFF indicator light turn on or off in accordance with the operation of the GTS.



Result:
Proceed to
OK
NG



OK

5.INSPECT VSC OFF SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.

Turn the ignition switch off.


b.
C374263C01
1.135,1.865 1.396,1.5 true 2.406,1.865 2.073,1.5 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 1.063,1.865 1.219,2.063 0.156,0.198 10 false + 2.427,1.885 2.583,2.083 0.156,0.198 10 false E
*a Component without harness connected
(VSC OFF switch)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the K39 VSC OFF switch connector.


d.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (+) - 2 (E) Switch pushed Below 1 Ω
5 (+) - 2 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-6 (CSW) - K39-5 (+) Always Below 1 Ω
A34-6 (CSW) or K39-5 (+) - Body ground Always 10 kΩ or higher
K39-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Multi Display All (White)
50004 409 20
Body Electrical > Combination Meter > Active Test
Tester Display
VSC OFF Indicator
50004 409 113

c.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG