Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1231  Steering Angle Sensor Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives steering angle sensor signals via CAN communication. When a malfunction occurs in the communication line with the steering angle sensor, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1231 Steering Angle Sensor Circuit While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self check (sensor malfunction). Steering angle sensor internal malfunction

WIRING DIAGRAM

C377599E05
0.802,0.677 1.417,0.875 0.615,0.198 10 false CANL 0.781,1.25 1.396,1.448 0.615,0.198 10 false CANH 0.885,1.75 1.5,1.948 0.615,0.198 10 false BAT 0.938,2.417 1.552,2.615 0.615,0.198 10 false IG1 0.865,3.302 1.479,3.5 0.615,0.198 10 false ESS 6.042,0.667 6.656,0.865 0.615,0.198 10 false CANL 6.031,1.26 6.646,1.458 0.615,0.198 10 false CANH 0.135,4.031 0.594,4.229 0.458,0.198 10 false K71 0.125,4.188 2.208,4.49 2.083,0.302 10 false Steering Angle Sensor 1.281,0.5 1.469,0.688 0.188,0.188 10 false 8 1.271,1.083 1.458,1.271 0.188,0.188 10 false 3 1.271,1.625 1.458,1.813 0.188,0.188 10 false 4 1.271,2.302 1.458,2.49 0.188,0.188 10 false 9 1.271,3.188 1.458,3.375 0.188,0.188 10 false 6 5.781,0.5 6.063,0.781 0.281,0.281 10 false 19 5.833,1.094 6.083,1.333 0.25,0.24 10 false 5 1.958,1.875 3.646,2.146 1.688,0.271 10 false ECU-DCC NO. 1 1.979,2.563 3.896,2.865 1.917,0.302 10 false ECU-IG1 NO. 2 3.563,1.74 5.25,2.01 1.688,0.271 10 false from Battery 3.573,2.406 5.26,2.677 1.688,0.271 10 false from IG1-NO. 1 Relay 2.969,3.542 4.896,3.844 1.927,0.302 10 false : CAN Communication Line 5.583,4.031 6.042,4.229 0.458,0.198 10 false A34 5.573,4.188 7.104,4.604 1.531,0.417 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

When U0126 is output together with C1231, inspect and repair the trouble areas indicated by U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


d.

Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
C1231 is output A
CAN communication system DTCs are output B
Speed sensor and/or yaw rate and acceleration sensor DTCs are output C
C1231 is not output D


HINT:
·

When CAN communication system DTCs are output, repair the CAN communication system before repairing each corresponding sensor.

·

If there is a malfunction in a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output even though the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.





A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

C

D

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C374262C01
0.229,0.771 0.615,1.01 0.385,0.24 2,1.99 2.604,1.635 true 2,2.375 2.604,2.823 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.313,0.813 0.771,1.01 0.458,0.198 10 false K71 2.667,2.76 3.125,2.958 0.458,0.198 10 false IG1 2.667,1.552 3.125,1.75 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Remove the steering wheel and column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



d.

Disconnect the K71 steering angle sensor connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-9 (IG1) - Body ground Ignition switch ON 11 to 14 V
K71-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C374262C04
0.229,0.771 0.615,1.01 0.385,0.24 1.323,2.385 0.76,2.823 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.313,0.813 0.771,1.01 0.458,0.198 10 false K71 0.448,2.781 0.906,2.979 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
K71-6 (ESS) - Body ground 1 minute after ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)