Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch to ON.

Conditions required for operation standby:

(a)

The driver door is closed.

(b)

The driver seat belt is fastened.

(c)

The system is normal.



WIRING DIAGRAM

C379806E06
0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.896,1.74 1.51,1.938 0.615,0.198 10 false CANH 0.104,3.917 0.719,4.115 0.615,0.198 10 false K21 0.104,4.094 2.031,4.375 1.927,0.281 10 false Combination Meter Assembly 1.396,0.75 1.708,0.948 0.313,0.198 10 false 31 1.385,1.552 1.698,1.75 0.313,0.198 10 false 32 5.083,0.75 5.396,0.948 0.313,0.198 10 false 19 5.156,1.552 5.469,1.75 0.313,0.198 10 false 5 4.719,2.625 4.823,2.833 0.104,0.208 10 false 1 4.448,2.844 4.865,3.094 0.417,0.25 10 false +B 3.813,2.844 4.26,3.104 0.448,0.26 10 false GND1 3.458,2.615 3.667,2.833 0.208,0.219 10 false 9 5.115,2.625 5.427,2.823 0.313,0.198 10 false 43 5.375,0.927 5.99,1.125 0.615,0.198 10 false CANL 5.375,1.74 5.99,1.938 0.615,0.198 10 false CANH 5.354,2.844 5.917,3.094 0.563,0.25 10 false HZRI 3.01,2.979 3.625,3.177 0.615,0.198 10 false K37 3.01,3.146 5.219,3.76 2.208,0.615 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 2.948,4.333 5.042,4.594 2.094,0.26 10 false : CAN Communication Line 6.49,2.74 7.104,2.938 0.615,0.198 10 false IC 5.302,3.948 5.917,4.146 0.615,0.198 10 false A34 5.302,4.104 6.854,4.49 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.583,2.76 2.333,2.969 0.75,0.208 10 false *1: for LHD 1.583,3.063 2.333,3.281 0.75,0.219 10 false *2: for RHD 3.594,2.448 3.906,2.646 0.313,0.198 10 false *1 4.823,2.458 5.156,2.677 0.333,0.219 10 false *1 3.594,2.615 3.771,2.833 0.177,0.219 10 false *2 4.833,2.625 5,2.823 0.167,0.198 10 false *2 4.719,2.458 4.875,2.656 0.156,0.198 10 false 8 3.396,2.448 3.635,2.635 0.24,0.188 10 false 16

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver door is closed.

2.

The driver seat belt is fastened.

3.

The system is normal.



Result:
Proceed to
NEXT



NEXT

2.CHECK CAN COMMUNICATION SYSTEM
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Hold Indicator
50004 409 117

d.

Check the combination meter assembly.

OK:

The brake hold standby indicator light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)

NG

5.PERFORM ACTIVE TEST USING GTS (BRAKE HOLD STANDBY INDICATOR LIGHT)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
BH Standby Light Brake hold standby indicator light Indicator light OFF/ON Observe combination meter assembly
Vehicle condition: Vehicle stopped
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BH Standby Light Brake hold standby indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
BH Standby Light
Data List Display
BH Standby Light
50004 105 73 280

b.

Check the operating condition of the brake hold standby indicator light when operating it using the GTS.


Result:
Result Proceed to
Brake hold standby indicator light in the Data List does not change using the Active Test. A
Brake hold standby indicator light in the Data List turns ON/OFF using the Active Test. B



A

B

6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.
C307484C40
2.26,1.177 2.135,0.552 true 2.042,1.844 2.26,1.417 true 1.24,1.188 1.115,0.563 true 0.865,1.823 1.177,1.427 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.958,0.375 2.708,0.594 0.75,0.219 10 false +B (*B) 1.823,1.875 2.573,2.115 0.75,0.24 10 false GND1 (*B) 0.917,0.375 1.604,0.594 0.688,0.219 10 false +B (*A) 0.594,1.875 1.333,2.115 0.74,0.24 10 false GND1 (*A)
*A for LHD
*B for RHD
*a Component without harness connected
(Brake Hold Switch (Electric Parking Brake Switch Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the K37 brake hold switch (electric parking brake switch assembly) connector.


d.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
8 (+B) - 16 (GND1) Switch pushed Below 1 Ω
8 (+B) - 16 (GND1) Switch not pushed 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
1 (+B) - 9 (GND1) Switch pushed Below 1 Ω
1 (+B) - 9 (GND1) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A34-43 (HZRI) - K37-8 (+B) Always Below 1 Ω
A34-43 (HZRI) or K37-8 (+B) - Body ground Always 10 kΩ or higher
K37-16 (GND1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A34-43 (HZRI) - K37-1 (+B) Always Below 1 Ω
A34-43 (HZRI) or K37-1 (+B) - Body ground Always 10 kΩ or higher
K37-9 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR