Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2017.09–2017.12
RM33A0E _59 Vehicle Exterior _065390 WINDOW / GLASS _0327255 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Forward recognition camera

·

Windshield glass


Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Forward recognition camera system

·

Lane departure alert system (w/ Steering Control)

·

Pre-collision system

·

Lighting System (EXT)


(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-collision system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 75536D 1.REMOVE WINDSHIELD OUTSIDE MOULDING LH

Hide 75535F 2.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

Hide 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53867H 6.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 7.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 55708 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 87810 9.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 8646C 10.REMOVE FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

Hide 89941 11.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 12.REMOVE ROOF HEADLINING ASSEMBLY

Hide 13.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.
B485027C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.


b.
B431533C04
2.396,1.01 2.854,1.229 false 2.229,1.281 2.677,1.708 false 1.385,0.25 1.688,0.542 false 1.177,0.177 1.49,0.333 0.313,0.156 10 false *1 2.927,1.167 3.24,1.323 0.313,0.156 10 false *2 2.74,1.635 3.052,1.792 0.313,0.156 10 false *a
*1 Windshield Glass
*2 Windshield Outside Moulding
*a Cut


Using a knife, cut off the windshield outside moulding as shown in the illustration.


c.
B469625C01
1.344,1.75 1.344,1.01 1.344,1.01 1.646,1.01 true 1.354,1.26 1.625,1.26 true 1.281,1.781 1.469,1.958 0.188,0.177 10 true *a
*a Matchmark


Place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



d.
B485032C01
1.198,0.5 1.729,0.844 1.729,0.844 2.229,0.51 false 0.99,1.51 1.229,1.281 false 1.688,1.625 1.927,1.396 false 1.677,0.875 1.844,1.063 0.167,0.188 10 true *1 1.979,1.302 2.208,1.479 0.229,0.177 10 true *2 1.26,1.198 1.49,1.385 0.229,0.188 10 true *a
*1 Windshield Glass Stopper
*2 Front Window Inner Center Moulding
*a Piano Wire


Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.

·

Be careful not to damage the front window inner center moulding.




g.

Disengage the windshield glass stoppers.

B485031C01
5.375,0.688 5.667,0.208 true 2.01,0.927 2.26,0.927 false 5.365,0.885 5.365,1.052 5.365,1.052 5.76,1.052 false 5.51,1.042 5.51,0.823 false 5.646,1.052 5.646,0.875 false 1.031,0.146 1.344,0.323 0.313,0.177 12 false *A 4.594,0.146 4.938,0.375 0.344,0.229 12 false *B 2.292,0.854 2.604,1.01 0.313,0.156 10 false *1 5.698,0.135 6,0.323 0.302,0.188 10 false *2 5.802,0.969 6.115,1.125 0.313,0.156 10 false *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting the adhesive.

·

To prevent the windshield glass sub-assembly from falling when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.



HINT:

Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.



h.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 14.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B479204C01
0.083,0.125 0.542,0.5 0.458,0.375 12 false *A
*A Back Side


Using a scraper, remove the 3 window glass adhesive dams.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dams with new ones.





Hide 75533G 15.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B469631C01
0.104,0.104 0.49,0.365 0.385,0.26 12 false *A
*A Back Side


Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 16.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B469632C01
0.094,0.104 0.469,0.344 0.375,0.24 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 17.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B469633C01
0.083,0.094 0.438,0.313 0.354,0.219 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 18.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B485033

Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56153C 19.REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B469634C01
1.594,2.563 1.594,2.385 1.594,2.385 2.104,2.385 false 1.833,2.385 1.833,2.573 false 0.094,0.073 0.448,0.302 0.354,0.229 12 false *A 2.135,2.313 2.448,2.469 0.313,0.156 10 false *a
*A Back Side
*a Matchmark


Place matchmarks on the windshield glass at the locations indicated in the illustration.


b.

Using a scraper, remove the front window inner center moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the front window inner center moulding with a new one.




Hide 20.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 21.CLEAN VEHICLE BODY

a.

Clean and shape the contact surface of the vehicle body.

i.
B470006C01
0.667,0.458 1.208,0.813 false 0.5,0.375 0.813,0.531 0.313,0.156 10 false *a 1.573,0.927 1.729,1.125 0.156,0.198 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surface of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.