Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327339 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1782  Rear Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The rear occupant classification sensor LH circuit consists of the occupant detection ECU and rear occupant classification sensor LH.

DTC B1782 is stored when a malfunction is detected in the rear occupant classification sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1782 Rear Occupant Classification Sensor LH Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the rear occupant classification sensor LH circuit.

·

Rear occupant classification sensor LH malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Rear occupant classification sensor LH (Front seat adjuster assembly RH)*

·

Occupant detection ECU



*: The rear occupant classification sensor LH is built into the front seat adjuster assembly RH.


WIRING DIAGRAM

B473427E06
4.094,2.927 5.865,3.458 1.771,0.531 10 false Occupant Detection ECU 4.104,2.771 5.375,3.167 1.271,0.396 10 false a19 0.552,2.938 3.042,3.438 2.49,0.5 10 false Rear Occupant Classification Sensor LH (Front Seat Adjuster Assembly RH) 0.552,2.771 4.51,3.438 3.958,0.667 10 false a23 4.125,0.854 4.75,1.229 0.625,0.375 10 false SVC3 1.521,1.948 2.146,2.323 0.625,0.375 10 false SIG 4.125,2.208 4.75,2.583 0.625,0.375 10 false SGD3 3.958,0.854 4.583,1.229 0.625,0.375 10 false 2 3.958,1.844 4.583,2.219 0.625,0.375 10 false 4 3.958,2.208 4.583,2.583 0.625,0.375 10 false 6 1.844,0.854 2.469,1.229 0.625,0.375 10 false 1 1.844,1.844 2.469,2.219 0.625,0.375 10 false 2 1.844,2.208 4.406,2.74 2.563,0.531 10 false 3 6.01,0.344 6.635,0.719 0.625,0.375 10 false 12 V 5.427,0.698 6.354,1.25 0.927,0.552 10 false Power Supply Control Circuit 5.385,1.688 6.417,2.083 1.031,0.396 10 false Communication Circuit 1.469,0.958 2.094,1.333 0.625,0.375 10 false SVC 4.125,1.844 4.75,2.219 0.625,0.375 10 false SIG3 1.469,2.313 2.094,2.688 0.625,0.375 10 false SGD

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

When DTC B1650 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1782 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and rear occupant classification sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and rear occupant classification sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH
a.
C295787C15
0.854,0.594 1.208,0.844 0.354,0.25 0.5,3.5 0.854,3.719 0.354,0.219 2.135,1.24 2.135,0.75 false 2.073,3.042 2.385,3.042 false 2.052,4.125 2.385,4.125 false 1.531,2.531 1.531,2.115 false 1.531,1.229 1.844,0.75 false 2.76,1.229 2.427,0.75 false 1.833,3.604 2.344,3.604 false 1.01,3.167 1.646,3.573 false 1.063,3.979 1.5,3.635 false 2.417,2.125 2.813,2.448 0.396,0.323 10 false *2 1.458,2.531 1.771,2.781 0.313,0.25 10 false *3 0.625,0.26 0.958,0.594 0.333,0.333 10 false *a 0.333,2.927 0.75,3.25 0.417,0.323 10 false *b 0.615,1.958 1.01,2.281 0.396,0.323 10 false *1 2.417,2.958 2.75,3.281 0.333,0.323 10 false *4 2.417,4.042 2.75,4.365 0.333,0.323 10 false *4 1.313,1.24 1.813,1.563 0.5,0.323 10 false SVC3 1.979,1.24 2.479,1.563 0.5,0.323 10 false SIG3 2.594,1.24 3.094,1.563 0.5,0.323 10 false SGD3 0.938,0.635 1.438,0.958 0.5,0.323 10 false a19 2.094,1.979 2.49,2.302 0.396,0.323 10 false A 1.813,1.979 2.208,2.302 0.396,0.323 10 false B 1.188,1.969 1.583,2.292 0.396,0.323 10 false C 0.906,1.969 1.302,2.292 0.396,0.323 10 false D 0.573,3.531 0.906,3.854 0.333,0.323 10 false a23 0.74,3.906 1.073,4.229 0.333,0.323 10 false SVC 0.74,3.094 1.073,3.417 0.333,0.323 10 false SIG 2.375,3.521 2.833,3.844 0.458,0.323 10 false SGD
*1 Rear Occupant Classification Sensor LH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Rear Occupant Classification Sensor LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a19-2 (SVC3) - Body ground Ignition switch ON Below 1 V
a19-4 (SIG3) - Body ground Ignition switch ON Below 1 V
a19-6 (SGD3) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-2 (SVC3) - a19-6 (SGD3) Always Below 1 Ω
a19-4 (SIG3) - a19-6 (SGD3) Always Below 1 Ω



h.

Disconnect the service wires from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-2 (SVC3) - a19-6 (SGD3) Always 1 MΩ or higher
a19-4 (SIG3) - a19-6 (SGD3) Always 1 MΩ or higher
a19-2 (SVC3) - a19-4 (SIG3) Always 1 MΩ or higher
a19-2 (SVC3) - Body ground Always 1 MΩ or higher
a19-4 (SIG3) - Body ground Always 1 MΩ or higher
a19-6 (SGD3) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and rear occupant classification sensor LH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

e.

Clear the DTCs stored in the airbag sensor assembly.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 10 seconds.


h.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1782 is not output.


HINT:

Codes other than DTC B1782 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK OCCUPANT DETECTION ECU
4.CHECK OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Replace the occupant detection ECU with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the occupant detection ECU.

Body Electrical > Occupant Detection > Clear DTCs
50002 394

f.

Clear the DTCs stored in the airbag sensor assembly.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 10 seconds.


i.

Check for DTCs.

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1782 is not output.


HINT:

Codes other than DTC B1782 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal.


l.

Restore the occupant detection ECU that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


Result:
Proceed to
OK
NG



OK

5.REPLACE OCCUPANT DETECTION ECU

NG

7.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
5.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


d.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Replace the front seat adjuster assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


d.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION
a.

Result:
Proceed to
NEXT



NEXT

END