The occupant classification system detects the front passenger seat condition. It then displays the instrument panel passenger airbag assembly and lower No. 2 instrument panel airbag assembly condition (activated/not activated) using the passenger airbag ON/OFF indicator.
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.
| Front Passenger Seat Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
| Vacant | OFF | ON | OFF |
| Adult*1 is seated | ON | OFF | OFF |
| Child*2 is seated | ON or OFF*2 | OFF or ON*2 | OFF |
| Child restraint system is installed | OFF | ON | OFF |
| Occupant classification system failure | OFF | ON | ON |
*1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.
*2: The system may not recognize a child or a child in a child restrain system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the ignition switch to ON, and check the SRS warning light condition.
After the primary check period, the SRS warning light turns off.
The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
"Zero Point Calibration is complete." is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Loosen the 4 installation bolts of the front seat assembly RH.
Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
"Zero Point Calibration is complete." is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Occupant Detection / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle SW | Front passenger side buckle switch | NG, Set or Unset | Set: Front passenger seat belt is fastened
Unset: Front passenger seat belt is not fastened |
"NG" will be displayed immediately after the ignition switch is turned to ON. |
| Tester Display |
|---|
| Passenger Buckle SW |
The GTS display changes correctly in accordance with the operation of the front passenger side buckle switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the occupant detection ECU, front occupant classification sensor LH and rear occupant classification sensor LH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the front occupant classification sensor LH and rear occupant classification sensor LH.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Connect the cable to the negative (-) battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat inner belt assembly RH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Connect the cable to the negative (-) battery terminal.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform Zero Point Calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT