Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327372 CYLINDER HEAD G

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for bank 1 and bank 2.

·

The following procedure is for bank 2.



PROCEDURE

Hide 11102 1.INSPECT CYLINDER HEAD LH

a.

Using a precision straightedge and feeler gauge, check the surfaces which contact the cylinder block sub-assembly and manifolds for warpage.

A366183C01
4.25,0.26 4.563,0.417 0.313,0.156 10 false *a 0.906,2.167 1.219,2.323 0.313,0.156 10 false *b 4.26,2.167 4.573,2.323 0.313,0.156 10 false *c
*a Bottom Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Standard Warpage:
Item Specified Condition
Bottom Side 0.05 mm (0.00197 in.)
Intake Manifold Side 0.08 mm (0.00315 in.)
Exhaust Manifold Side 0.08 mm (0.00315 in.)


Maximum Warpage:
Item Specified Condition
Bottom Side 0.10 mm (0.00394 in.)
Intake Manifold Side 0.10 mm (0.00394 in.)
Exhaust Manifold Side 0.10 mm (0.00394 in.)


HINT:

If the warpage is more than the maximum, replace the cylinder head LH.



Hide 11102 2.INSPECT CYLINDER HEAD LH FOR CRACKS

a.
A366184

Using a dye penetrant, check the intake ports, exhaust ports and bottom surface of the cylinder head LH for cracks.

HINT:

If cracks are found, replace the cylinder head LH.



Hide 13711 3.INSPECT INTAKE VALVE

a.
A366185

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


HINT:

If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.



b.
A366186C01
0.344,1.792 0.656,1.948 0.313,0.156 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the intake valve.



c.
A366187C01
1.958,0.979 2.271,1.135 0.313,0.156 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:

105.85 mm (4.17 in.)


Minimum Overall Length:

105.35 mm (4.15 in.)


HINT:

If the overall length is less than the minimum, replace the intake valve.



Hide 13715 4.INSPECT EXHAUST VALVE

a.
A366188

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


HINT:

If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.



b.
A366189C01
0.375,1.729 0.688,1.885 0.313,0.156 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the exhaust valve.



c.
A366190C01
1.969,1.01 2.281,1.167 0.313,0.156 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:

110.40 mm (4.35 in.)


Minimum Overall Length:

109.90 mm (4.33 in.)


HINT:

If the overall length is less than the minimum, replace the exhaust valve.



Hide 11131 5.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the intake valve seat.

NOTICE:

Do not rotate the intake valve while pressing it.



c.
A366191C01
1.427,1.031 1.74,1.188 0.313,0.156 10 false *a
*a Width


Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the intake valve.



ii.

If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the intake valve seat.



iii.

Measure the width of the contact area of the intake valve seat and valve face.

Standard Width:

1.1 to 1.5 mm (0.0433 to 0.0591 in.)




Hide 11135 6.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the exhaust valve seat.

NOTICE:

Do not rotate the exhaust valve while pressing it.



c.
A366192C01
1.417,1.052 1.729,1.208 0.313,0.156 10 false *a
*a Width


Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the exhaust valve.



ii.

If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the exhaust valve seat.



iii.

Measure the width of the contact area of the exhaust valve seat and valve face.

Standard Width:

1.1 to 1.5 mm (0.0433 to 0.0591 in.)




Hide 13711B 7.INSPECT INNER COMPRESSION SPRING

a.
A366193

Using a vernier caliper, measure the free length of the inner compression spring.

Standard Free Length:

54.53 mm (2.15 in.)


Minimum Free Length:

52.43 mm (2.06 in.)


HINT:

If the free length is not as specified, replace the inner compression spring.



b.
A366194C01
1.823,0 2.135,0.156 0.313,0.156 10 false *a 0.927,1.25 1.24,1.406 0.313,0.156 10 false *b
*a Deviation
*b 40 mm (1.57 in.)


Using a steel square, measure the deviation of the inner compression spring.

Maximum Deviation (Reference):

1.4 mm (0.0551 in.)


HINT:

If the deviation is more than the maximum, replace the inner compression spring.



Hide 8.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A366195

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.12 mm (0.00472 in.)
Exhaust 0.12 mm (0.00472 in.)


HINT:

If the oil clearance is more than the maximum, replace the valve and valve guide bush.