Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327372 CYLINDER HEAD A

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for bank 1 and bank 2.

·

The following procedure is for bank 2.



PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head LH, the spark plug tubes must be replaced.


a.
A366206C01
1.771,0.417 2.083,0.573 0.313,0.156 10 false *a 1.604,1.896 1.917,2.052 0.313,0.156 10 false *b
*a Application Width
*b 9.0 to 15.0 mm (0.354 to 0.591 in.)


Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


NOTICE:

Install the spark plug tube within 3 minutes of applying adhesive.



b.
A375174C01
0.76,0.219 1.031,0.219 1.031,0.219 1.302,0.708 true 2.813,2.833 2.594,2.833 2.594,2.833 2.396,3.333 true 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 2.229,3 2.542,3.156 0.313,0.156 10 false *b 2.854,2.771 3.167,2.927 0.313,0.156 10 false *c
*a Wooden Block
*b Protrusion Height
*c Cylinder Head LH Top Surface


Using a hammer and wooden block, tap in the 3 spark plug tubes to the specified protrusion height.

Standard Protrusion Height:

73 mm (2.87 in.)


NOTICE:
·

Do not tap in the spark plug tube more than specified.

·

Do not start the engine for at least 1 hour after installation.

·

Be careful not to deform the spark plug tubes.

·

Be careful not to let adhesive drip into the cylinder head LH.




Hide 11117G 2.INSTALL NO. 3 STRAIGHT SCREW PLUG

a.
A366165

Using a 10 mm hexagon socket wrench, install 4 new cylinder head screw plug gaskets and the 4 No. 3 straight screw plugs to the cylinder head LH.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

NOTICE:
·

Do not apply adhesive to the No. 3 straight screw plug.

·

The cylinder head screw plug gasket for the No. 3 straight screw plug is not the same as the water hole gasket for the No. 1 straight screw plug.




Hide 11117F 3.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A366182

Using a 14 mm hexagon wrench, install a new cylinder head screw plug gasket and the No. 2 straight screw plug to the cylinder head LH.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 11117E 4.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.

Apply adhesive to the 2 No. 1 straight screw plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the 2 No. 1 straight screw plugs within 3 minutes of applying adhesive.



b.
A366181

Using a 10 mm hexagon socket wrench, install 2 new water hole gaskets and the 2 No. 1 straight screw plugs to the cylinder head LH.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the 12 valve spring seats to the cylinder head LH.


Hide 13711E 6.INSTALL INTAKE VALVE STEM OIL SEAL

a.
A366210C01
0.927,0.656 0.604,0.375 false 2.438,0.656 2.792,0.406 false 0.427,0.26 0.74,0.417 0.313,0.156 10 false *a 2.833,0.26 3.146,0.417 0.313,0.156 10 false *b 0.823,1.677 1.135,1.833 0.313,0.156 10 false *c 2.385,1.677 2.698,1.833 0.313,0.156 10 false *d
*a Gray
*b Black
*c Intake Side
*d Exhaust Side


Apply a light coat of engine oil to a new intake valve stem oil seal.

NOTICE:

Make sure to install each valve stem oil seal to the correct side. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve stem oil seals are gray and the exhaust valve stem oil seals are black.



b.
A366211C01
1.375,0.813 1.438,0.427 1.438,0.427 1.625,0.427 true 2.729,1.958 2.729,1.25 2.729,1.25 2.833,1 true 2.677,1.979 2.99,2.135 0.313,0.156 10 true *1 0.979,2.26 1.292,2.417 0.313,0.156 10 false *a 2.25,2.26 2.563,2.417 0.313,0.156 10 false *b 1.646,0.344 2.104,0.542 0.458,0.198 10 true SST
*1 Valve Stem Oil Seal
*a Correct
*b Incorrect


Using SST, push in the 6 intake valve stem oil seals to the intake valve guide bush.

SST
09201-41020  

NOTICE:
·

Failure to use SST will cause the intake valve stem oil seal to be damaged or improperly seated.

·

Do not push in the intake valve stem oil seal at an angle.




Hide 13715A 7.INSTALL EXHAUST VALVE STEM OIL SEAL

HINT:

Use the same procedure as for the intake side.


Hide 13715 8.INSTALL EXHAUST VALVE

a.
A366212C01
2.635,1.375 2.948,1.531 0.313,0.156 10 false *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A366213C01
1.052,0.646 1.531,0.646 false 1,1.438 1.479,1.438 false 2.104,1.865 2.448,1.635 false 0.802,1.365 1.115,1.521 0.313,0.156 10 false *2 0.854,0.583 1.167,0.74 0.313,0.156 10 false *1 2.51,1.542 2.823,1.698 0.313,0.156 10 false *3
*1 Valve Spring Retainer
*2 Inner Compression Spring
*3 Cylinder Head LH
V100135

Top Side


Install the 6 exhaust valves, 6 inner compression springs and 6 valve spring retainers to the cylinder head LH.

NOTICE:
·

Install the inner compression spring with its tapered side facing upward (towards the valve spring retainer).

·

Install the same parts in the same combination to their original locations.




c.
A366178C01
2.104,1.177 1.625,0.313 1.625,0.313 2.188,0.438 true 2.552,2.021 2.844,2.021 false 1.323,0.229 1.781,0.427 0.458,0.198 10 false SST 2.917,1.927 3.229,2.083 0.313,0.156 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and install the 6 valve spring retainer locks to the valve spring retainer.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

NOTICE:

Install the same parts in the same combination to their original locations.



d.
A366215C01
2.219,0.771 2.604,0.438 false 2.615,1.979 2.917,1.979 false 2.635,0.323 2.948,0.479 0.313,0.156 10 false *a 2.958,1.906 3.271,2.063 0.313,0.156 10 false *b
*a Plastic Hammer
*b Wooden Block


Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.




Hide 13711 9.INSTALL INTAKE VALVE

a.
A366216C01
2.552,1.385 2.865,1.542 0.313,0.156 10 false *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.
A366213C01
1.052,0.646 1.531,0.646 false 1,1.438 1.479,1.438 false 2.104,1.865 2.448,1.635 false 0.802,1.365 1.115,1.521 0.313,0.156 10 false *2 0.854,0.583 1.167,0.74 0.313,0.156 10 false *1 2.51,1.542 2.823,1.698 0.313,0.156 10 false *3
*1 Valve Spring Retainer
*2 Inner Compression Spring
*3 Cylinder Head LH
V100135

Top Side


Install the 6 intake valves, 6 inner compression springs and 6 valve spring retainers to the cylinder head LH.

NOTICE:
·

Install the inner compression spring with its tapered side facing upward (towards the valve spring retainer).

·

Install the same parts in the same combination to their original locations.




c.
A366177C01
1.344,0.281 1.833,0.281 1.833,0.281 1.552,1.104 true 2.115,1.844 2.469,1.844 false 0.177,1.323 0.323,1.229 false 1.885,0.208 2.344,0.406 0.458,0.198 10 false SST 2.521,1.76 2.833,1.917 0.313,0.156 10 false *a 0.021,1.271 0.333,1.427 0.313,0.156 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and install the 6 valve spring retainer locks to the valve spring retainer.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

NOTICE:

Install the same parts in the same combination to their original locations.



d.
A366219C01
2.01,0.729 2.427,0.313 true 2.51,1.885 2.813,1.885 false 2.479,0.167 2.792,0.323 0.313,0.156 10 false *a 2.875,1.802 3.188,1.958 0.313,0.156 10 false *b
*a Plastic Hammer
*b Wooden Block


Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.