Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.09–2017.12
RM33A0E _53 Suspension _065363 TIRE PRESSURE MONITORING _0327403 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2121/21  No Signal from Transmitter ID1  C2122/22  No Signal from Transmitter ID2  C2123/23  No Signal from Transmitter ID3  C2124/24  No Signal from Transmitter ID4  C2181/81  Transmitter ID1 not Received (Test Mode DTC)  C2182/82  Transmitter ID2 not Received (Test Mode DTC)  C2183/83  Transmitter ID3 not Received (Test Mode DTC)  C2184/84  Transmitter ID4 not Received (Test Mode DTC)  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.

Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.

·

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

·

Devices using similar radio frequencies are used in the vehicle.

·

The ID of a tire pressure warning valve and transmitter is mistyped during registration.

·

A tire, wheel and/or transmitter from a different vehicle is installed.


HINT:

When no transmitter ID is received from a tire pressure warning valve and transmitter for 10 minutes or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 10 minutes or more, DTCs from C2121/21 to C2124/24 are stored.

DTCs C2121/21 to C2124/24 can only be cleared by using the GTS. DTCs C2181/81 to C2184/84 can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181/81 to C2184/84 are output only in test mode.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2121/21 No Signal from Transmitter ID1 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2122/22 No Signal from Transmitter ID2 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2123/23 No Signal from Transmitter ID3 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2124/24 No Signal from Transmitter ID4 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 10 minutes or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2181/81 Transmitter ID1 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2182/82 Transmitter ID2 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2183/83 Transmitter ID3 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-
C2184/84 Transmitter ID4 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


-

NOTICE:
·

When DTCs C2121/21 to C2124/24 are set, DTC C2179/79 may be set simultaneously. In such cases, troubleshoot DTCs C2121/21 to C2124/24 first, then troubleshoot DTC C2179/79.

·

If the GTS is used to display the Data List for 10 minutes or more, the tire pressure warning ECU stores DTCs C2121/21 to C2124/24. If these DTCs are stored, clear the DTCs using the GTS.

·

If any DTC from C2121/21 to C2124/24 is output, clear the DTCs or drive the vehicle at 40 km/h (25 mph) for 1 minute or more after repairing the malfunctions.



HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

C379802E03
3.146,0.146 4.51,0.521 1.365,0.375 10 false Tire Pressure Warning Valve and Transmitter 1.427,2.844 3.073,3.229 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.438,2.677 1.781,2.875 0.344,0.198 10 false K53 3.479,2.688 3.823,2.885 0.344,0.198 10 false RDA 3.479,3.125 3.823,3.323 0.344,0.198 10 false PRG 6,2.677 6.344,2.875 0.344,0.198 10 false RDA 6.01,3.125 6.354,3.323 0.344,0.198 10 false PRG 2.646,3.708 3.521,4.135 0.875,0.427 10 false Tire Pressure Warning Light 2.594,4.24 2.938,4.438 0.344,0.198 10 false ES 2.583,4.781 3.031,5 0.448,0.219 10 false MSTI 2.583,5.188 3.094,5.417 0.51,0.229 10 false MSM+ 3.646,3.813 3.99,4.01 0.344,0.198 10 false INT 6,3.813 6.521,4.094 0.521,0.281 10 false CLSW 3.896,2.573 4.24,2.771 0.344,0.198 10 false 10 3.906,3.01 4.24,3.219 0.333,0.208 10 false 11 5.75,2.563 6.094,2.76 0.344,0.198 10 false 4 5.75,3.031 6.094,3.229 0.344,0.198 10 false 5 5.76,3.708 6.104,3.906 0.344,0.198 10 false 3 4.01,3.698 4.354,3.896 0.344,0.198 10 false 4 2.323,4.115 2.667,4.313 0.344,0.198 10 false 21 2.313,4.667 2.656,4.865 0.344,0.198 10 false 29 2.302,5.083 2.646,5.281 0.344,0.198 10 false 28 1.948,5.948 2.292,6.146 0.344,0.198 10 false K22 1.948,6.375 2.292,6.573 0.344,0.198 10 false K22 1.948,6.771 2.292,6.969 0.344,0.198 10 false K22 3.396,5.979 3.74,6.177 0.344,0.198 10 false z1 3.406,6.375 3.75,6.573 0.344,0.198 10 false z1 3.406,6.771 3.75,6.969 0.344,0.198 10 false z1 3.427,5.792 3.771,5.99 0.344,0.198 10 false 5 3.427,6.188 3.771,6.385 0.344,0.198 10 false 4 3.396,6.594 3.74,6.792 0.344,0.198 10 false 10 5.677,6.604 7.073,7.063 1.396,0.458 10 false Tire Pressure Warning ECU and Receiver 5.667,6.427 6.01,6.625 0.344,0.198 10 false R9 5.688,5.833 6.031,6.031 0.344,0.198 10 false 12 5.99,5.948 6.51,6.229 0.521,0.281 10 false GND 1.979,5.76 2.323,5.958 0.344,0.198 10 false 10 1.969,6.188 2.302,6.396 0.333,0.208 10 false 11 2.01,6.594 2.354,6.792 0.344,0.198 10 false 4 4,4.354 4.344,4.552 0.344,0.198 10 false K21 4,4.521 5.177,4.906 1.177,0.385 10 false Combination Meter Assembly 2.229,7.167 3.323,7.563 1.094,0.396 10 false Spiral Cable Sub-assembly 3.656,7.167 4.927,7.521 1.271,0.354 10 false Steering Pad Switch Assembly 0.604,8.094 2.198,8.323 1.594,0.229 10 false : Radio Waves 0.594,8.479 2.896,8.708 2.302,0.229 10 false : CAN Communication Line 2.323,5.896 2.771,6.115 0.448,0.219 10 false +DP2 2.313,6.281 2.76,6.5 0.448,0.219 10 false +DP 2.333,6.677 2.781,6.896 0.448,0.219 10 false EAU 3.156,1.177 4.521,1.552 1.365,0.375 10 false Tire Pressure Warning Valve and Transmitter 0.656,0.615 2.021,0.99 1.365,0.375 10 false Tire Pressure Warning Valve and Transmitter 0.667,1.625 2.031,2 1.365,0.375 10 false Tire Pressure Warning Valve and Transmitter

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver or tire pressure warning valve and transmitter, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking for 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.




Result:
Result Proceed to
There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. A
There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. B



A

2.CONFIRM OUTPUT DTC

B

10.CLEAR DTC
2.CONFIRM OUTPUT DTC
a.

Check the stored DTC.


Result:
Result Proceed to
Any DTCs from C2121/21 to C2124/24 are output (C2181/81 to C2184/84 when in Test Mode) A
All DTCs from C2121/21 to C2124/24 are output (C2181/81 to C2184/84 when in Test Mode) B



A

3.IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

B

5.TEST MODE INSPECTION (C2181/81 to C2184/84)
3.IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Display the "ID Tire Position" value for each wheel using the GTS.


g.

Refer to the following chart and check the wheel position of the DTC and transmitter match.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Position ID1 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID1 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 2 Tire Position ID2 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID2 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 3 Tire Position ID3 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID3 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 4 Tire Position ID4 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID4 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
HINT:

Refer to the following chart for the Data List items that correspond to the DTCs.

DTC No. Detection Item Data List
C2121/21 No Signal from Transmitter ID1 ID1 Tire Position
C2181/81 Transmitter ID 1 not Received (for Test Diagnosis)
C2122/22 No Signal from Transmitter ID2 ID2 Tire Position
C2182/82 Transmitter ID 2 not Received (for Test Diagnosis)
C2123/23 No Signal from Transmitter ID3 ID3 Tire Position
C2183/83 Transmitter ID 3 not Received (for Test Diagnosis)
C2124/24 No Signal from Transmitter ID4 ID4 Tire Position
C2184/84 Transmitter ID 4 not Received (for Test Diagnosis)


Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Position
ID 2 Tire Position
ID 3 Tire Position
ID 4 Tire Position
50003 203 78,54,55,56

Result:
Proceed to
NEXT



NEXT

4.CHECK TRANSMITTER ID
4.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Refer to the following chart and record the tire pressure warning valve and transmitter ID of the output DTC.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
HINT:
·

*1: Displayed only when the ID No. is not registered.

·

Refer to the following chart for the Data List items that correspond to the DTCs.

DTC No. Detection Item Data List
C2121/21 No Signal from Transmitter ID1 Registered ID 1 code
C2181/81 Transmitter ID 1 not Received (for Test Diagnosis)
C2122/22 No Signal from Transmitter ID2 Registered ID 2 code
C2182/82 Transmitter ID 2 not Received (for Test Diagnosis)
C2123/23 No Signal from Transmitter ID3 Registered ID 3 code
C2183/83 Transmitter ID 3 not Received (for Test Diagnosis)
C2124/24 No Signal from Transmitter ID4 Registered ID 4 code
C2184/84 Transmitter ID 4 not Received (for Test Diagnosis)



Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10

g.

Disassemble the tire indicated in the output DTC and check the tire pressure warning valve and transmitter ID.


C317550C04
6.083,1.313 6.24,0.646 6.24,0.646 6.375,0.646 false 1.365,1.656 0.917,1.229 0.917,1.229 0.729,1.229 false 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.417,0.573 6.729,0.771 0.313,0.198 10 false *a 0.5,1.146 0.813,1.344 0.313,0.198 10 false *b
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) *b Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark


NOTICE:

For vehicles equipped with the wheel speed type tire inflation pressure display function, be sure to use tire pressure warning valve and transmitters with identification marks.


h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B



A

REPLACE CORRESPONDING TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

7.REGISTRATION OF TRANSMITTER ID
5.TEST MODE INSPECTION (C2181/81 to C2184/84)
a.

Perform a test mode inspection and perform Transmitter Data Reception Check (C2181/81 to C2184/84).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE


Result:
Proceed to
OK
NG



OK

END

Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.


NG

6.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER
6.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
HINT:
·

*1: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.



Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10

g.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.


C348690C01
0.667,0.833 0.927,0.833 0.927,0.833 1.333,1.667 true 5.979,1.344 6.167,0.667 6.167,0.667 6.417,0.667 true 0.25,0.115 0.563,0.313 0.313,0.198 10 false *1 0.479,0.76 0.792,0.958 0.313,0.198 10 false *b 6.458,0.594 6.771,0.792 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) *b Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark


NOTICE:

For vehicles equipped with the wheel speed type tire inflation pressure display function, be sure to use tire pressure warning valve and transmitters with identification marks.


h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

7.REGISTRATION OF TRANSMITTER ID
7.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

Result:
Proceed to
NEXT



NEXT

END

10.CLEAR DTC
a.

Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

Result:
Proceed to
NEXT



NEXT

END

Explain to the customer that there is a high possibility that a device (located near or inside the vehicle) or facility using electrical waves of approximately the same frequency is causing electrical wave interference.