Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Blind Spot Monitor Master" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Blind Spot Monitor Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Blind spot monitor sensor RH branch line or connector

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor RH



WIRING DIAGRAM

C350998E39
0.24,1.844 0.698,2.042 0.458,0.198 10 false R98 0.583,1.844 2.635,2.146 2.052,0.302 10 false No. 5 CAN Junction Connector 1.667,1.344 2.125,1.542 0.458,0.198 10 false 13 1.698,0.75 2.156,0.948 0.458,0.198 10 false 3 5.323,0.729 5.781,0.927 0.458,0.198 10 false 2 5.323,1.323 5.781,1.521 0.458,0.198 10 false 7 5.625,0.875 6.083,1.073 0.458,0.198 10 false CA1P 5.604,2.469 6.063,2.667 0.458,0.198 10 false BRB 5.625,1.458 6.083,1.656 0.458,0.198 10 false CA1N 5.344,2.344 5.802,2.542 0.458,0.198 10 false 5 5.604,3.063 6.063,3.26 0.458,0.198 10 false BRGD 5.292,2.938 5.75,3.135 0.458,0.198 10 false 10 3.688,2.333 4.75,2.594 1.063,0.26 10 false ECU-IG1 NO. 4 1.625,2.469 3.104,2.75 1.479,0.281 10 false from IG1-NO. 1 Relay 5.24,4.083 5.698,4.281 0.458,0.198 10 false W5 5.542,4.083 6.719,4.469 1.177,0.385 10 false Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the W5 blind spot monitor sensor RH connector.


c.
C346738C26
1.469,0.719 1.938,0.979 0.469,0.26 1.365,1.135 1.531,1.135 1.531,1.135 1.531,1.885 true 1.375,2.917 1.542,2.917 1.542,2.917 1.542,2.167 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.594,0.76 1.885,0.979 0.292,0.219 10 false W5 0.938,1.073 1.552,1.271 0.615,0.198 10 false CA1P 0.969,2.844 1.583,3.042 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-2 (CA1P) - W5-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346738C27
1.469,0.719 1.885,1 0.417,0.281 2.188,1.156 2.021,1.156 2.021,1.156 2.021,1.906 true 2.208,2.844 2.042,2.844 2.042,2.844 2.042,2.177 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 1.573,0.781 2.115,1.094 0.542,0.313 10 false W5 2.26,1.073 2.875,1.271 0.615,0.198 10 false BRB 2.281,2.76 2.896,2.958 0.615,0.198 10 false BRGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-10 (BRGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W5-5 (BRB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)