Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2017.09–2018.04
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Door Mirror ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Door Mirror ECU LH Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Front Door LH/L-Mirror (FL-Door/L-Mirror)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Door Mirror ECU LH Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Outer mirror control ECU assembly (for front passenger side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for front passenger side)

·

Outer mirror control ECU assembly (for front passenger side) ground circuit

·

Outer mirror control ECU assembly (for front passenger side)



WIRING DIAGRAM

C382030E03
0.313,1.938 0.771,2.135 0.458,0.198 10 false R94 0.646,1.938 2.604,2.146 1.958,0.208 10 false No. 1 Junction Connector 1.719,1.396 2.177,1.594 0.458,0.198 10 false 12 1.74,0.833 2.198,1.031 0.458,0.198 10 false 1 5.406,0.833 5.844,1.063 0.438,0.229 10 false 9 5.406,1.385 5.844,1.615 0.438,0.229 10 false 8 5.677,0.948 6.219,1.188 0.542,0.24 10 false CANP 5.667,1.51 6.208,1.75 0.542,0.24 10 false CANN 5.667,4.094 6.208,4.333 0.542,0.24 10 false GND 5.396,3.969 5.938,4.208 0.542,0.24 10 false 7 4.583,4.854 5.125,5.094 0.542,0.24 10 false O8 4.875,4.854 7.094,5.292 2.219,0.438 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 5.667,3.49 6.208,3.729 0.542,0.24 10 false BDR 5.667,2.906 6.208,3.146 0.542,0.24 10 false CPUB 5.667,2.313 6.208,2.552 0.542,0.24 10 false SIG 3.792,2.156 4.844,2.479 1.052,0.323 10 false ECU-IG1 NO. 4 3.979,3.333 5.396,3.656 1.417,0.323 10 false DOOR F/L 3.802,2.75 5.219,3.073 1.417,0.323 10 false ECU-DCC NO. 2 2.198,3.479 3.031,3.802 0.833,0.323 10 false from Battery 2.188,2.896 3.021,3.219 0.833,0.323 10 false from Battery 1.656,2.302 3.281,2.813 1.625,0.51 10 false from IG1-NO. 1 Relay 5.354,3.375 5.896,3.615 0.542,0.24 10 false 14 5.396,2.781 5.938,3.021 0.542,0.24 10 false 6 5.385,2.208 5.927,2.448 0.542,0.24 10 false 5

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the O8 outer mirror control ECU assembly (for front passenger side) connector.


c.
C381598C20
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.521,0.375 1.906,0.635 0.385,0.26 10 false O8 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O8-9 (CANP) - O8-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C381598C11
1.427,0.323 1.854,0.594 0.427,0.271 2.229,2.073 2.229,2.656 2.229,2.656 2.396,2.656 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 1.854,1.688 1.854,0.833 1.854,0.833 1.688,0.833 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.552,0.385 1.938,0.646 0.385,0.26 10 false O8 1.375,0.76 1.854,1 0.479,0.24 10 false SIG 2.49,2.573 2.969,2.813 0.479,0.24 10 false BDR 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O8-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O8-6 (CPUB) - Body ground Always 11 to 14 V
O8-14 (BDR) - Body ground Always 11 to 14 V
O8-5 (SIG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)