The tilt motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor (steering column assembly) detects the tilt angle of the steering column assembly and sends a signal to the multiplex tilt and telescopic ECU based on that angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B261096 | Tilt Position Sensor or Tilt Motor Circuit Component Internal Failure | Tilt operation stops within the operation range while operating. | ·
TI & TE Fuse ·
Tilt position sensor (steering column assembly) ·
Tilt motor (steering column assembly) ·
Harness or connector ·
Multiplex tilt and telescopic ECU |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Check that the steering wheel tilts up and down.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
| Tester Display |
|---|
| Tilt Motor |
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Tilt Motor | Tilt operation | UP/DOWN |
The steering wheel tilts up and down.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Disconnect the K91 tilt motor (steering column assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-13 (VCI) - K91-4 (VCI) | Always | Below 1 Ω |
| K72-16 (TIS) - K91-5 (TIS) | Always | Below 1 Ω |
| K72-4 (E1) -K91-6 (E1) | Always | Below 1 Ω |
| K72-13 (VCI) or K91-4 (VCI) - Body ground | Always | 10 kΩ or higher |
| K72-16 (TIS) or K91-5 (TIS) - Body ground | Always | 10 kΩ or higher |
| K72-4 (E1) or K91-6 (E1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-1 (GND) - Body ground | Always | Below 1 Ω |
| K72-8 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K72 multiplex tilt and telescopic ECU connector.
| *a | Component with harness connected
(Multiplex Tilt and Telescopic ECU) |
Disconnect the K91 tilt motor (steering column assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-13 (VCI) - K72-4 (E1) | Engine switch on (IG) | 8 to 14 V |
| K72-16 (TIS) - K72-4 (E1) | Engine switch on (IG) | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Tilt Motor (Steering Column Assembly)) |
Reconnect the K72 multiplex tilt and telescopic ECU connector.
Reconnect the K91 tilt motor (steering column assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K91-5 (TIS) - K91-6 (E1) | Steering wheel tilting up or tilting down | Pulse generation
High: 8 to 14 V Low: Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-2 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-1 (GND) - Body ground | Always | Below 1 Ω |
| K72-8 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K72 multiplex tilt and telescopic ECU connector.
Disconnect the K91 tilt motor (steering column assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K72-7 (TIM+) - K91-1 (TIM+) | Always | Below 1 Ω |
| K72-20 (TIM-) - K91-2 (TIM-) | Always | Below 1 Ω |
| K72-7 (TIM+) or K91-1 (TIM+) - Body ground | Always | 10 kΩ or higher |
| K72-20 (TIM-) or K91-2 (TIM-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K91 tilt motor (steering column assembly) connector.
| *a | Component without harness connected
(Tilt Motor (Steering Column Assembly)) |
Apply 12 V battery voltage to the tilt motor (steering column assembly) connector. Then check the steering wheel tilt operation.
| Measurement Condition | Specified Condition |
|---|---|
·
12 V battery positive (+) lead → K91-1 (TIM+) ·
12 V battery negative (-) lead → K91-2 (TIM-) |
The steering wheel tilts up. |
·
12 V battery positive (+) lead → K91-2 (TIM-) ·
12 V battery negative (-) lead → K91-1 (TIM+) |
The steering wheel tilts down. |
| Proceed to |
|---|
| OK |
| NG |
OK
NG