Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM33A0E _55 Steering _065371 STEERING COLUMN _0327498 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B261196  Telescopic Position Sensor or Telescopic Motor Circuit Component Internal Failure  


DESCRIPTION

The telescopic motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column assembly forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor (steering column assembly) detects the sliding position of the steering column assembly in the forward and backward directions and sends a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

DTC No. Detection Item DTC Detection Condition Trouble Area
B261196 Telescopic Position Sensor or Telescopic Motor Circuit Component Internal Failure Telescopic operation stops within the operation range while operating.
·

TI & TE Fuse

·

Telescopic position sensor (steering column assembly)

·

Telescopic motor (steering column assembly)

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C244373E33
2.125,0.896 2.99,1.365 0.865,0.469 10 false from Battery 3.521,1.042 4.031,1.188 0.51,0.146 10 false TI & TE 4.698,0.875 4.99,1.021 0.292,0.146 10 false +B 4.531,0.792 4.635,0.938 0.104,0.146 10 false 2 1.677,1.198 2.094,1.344 0.417,0.146 10 false TEM+ 2.135,1.99 2.25,2.135 0.115,0.146 10 false 1 1.677,1.99 2.104,2.135 0.427,0.146 10 false TEM- 2.146,1.198 2.26,1.344 0.115,0.146 10 false 4 1.75,2.76 2.229,2.906 0.479,0.146 10 false VCE 2.146,2.74 2.25,2.906 0.104,0.167 10 false 6 1.76,3.156 2.094,3.302 0.333,0.146 10 false TES 2.146,3.146 2.26,3.313 0.115,0.167 10 false 7 1.865,3.552 2.063,3.698 0.198,0.146 10 false E2 2.146,3.531 2.26,3.698 0.115,0.167 10 false 8 0.771,1.469 2,1.677 1.229,0.208 10 false Telescopic Motor 4.677,1.177 5.094,1.375 0.417,0.198 10 false TEM+ 4.677,1.958 5.052,2.156 0.375,0.198 10 false TEM- 4.688,2.729 5.01,2.927 0.323,0.198 10 false VCE 4.688,3.125 5.021,3.323 0.333,0.198 10 false TES 4.688,3.521 4.938,3.719 0.25,0.198 10 false E2 0.49,3.813 1.781,4.219 1.292,0.406 10 false Telescopic Position Sensor 4.448,1.979 4.635,2.177 0.188,0.198 10 false 19 4.448,2.729 4.635,2.938 0.188,0.208 10 false 14 4.448,3.135 4.76,3.344 0.313,0.208 10 false 15 4.688,4.74 5.021,4.938 0.333,0.198 10 false K72 4.531,1.188 4.771,1.385 0.24,0.198 10 false 6 4.51,3.833 4.75,4.031 0.24,0.198 10 false 8 4.448,3.531 4.76,3.729 0.313,0.198 10 false 17 4.677,3.833 5.24,4.031 0.563,0.198 10 false GND2 4.521,4.24 4.76,4.438 0.24,0.198 10 false 1 4.677,4.323 5.24,4.521 0.563,0.198 10 false GND 6.021,1.021 6.333,1.219 0.313,0.198 10 false +B 6.021,1.813 6.333,2.01 0.313,0.198 10 false +B 6.083,3.031 6.49,3.229 0.406,0.198 10 false 12 V 6.031,3.729 6.604,3.927 0.573,0.198 10 false to CPU 4.688,4.917 6.833,5.115 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.438,4.927 3.333,5.292 2.896,0.365 10 false Telescopic Motor (Steering Column Assembly) 0.448,4.74 0.792,4.938 0.344,0.198 10 false K92

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TELESCOPIC MOTOR)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Check that the steering column contracts and extends.


f.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display
Telescopic Motor
50004 406 42001
Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range
Telescopic Motor Telescopic Operation LONG/SHORT
OK:

The steering column contracts and extends.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR (STEERING COLUMN ASSEMBLY))

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR (STEERING COLUMN ASSEMBLY))
a.

Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Disconnect the K92 telescopic motor (steering column assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-14 (VCE) - K92-6 (VCE) Always Below 1 Ω
K72-15 (TES) - K92-7 (TES) Always Below 1 Ω
K72-17 (E2) - K92-8 (E2) Always Below 1 Ω
K72-14 (VCE) or K92-6 (VCE) - Body ground Always 10 kΩ or higher
K72-15 (TES) or K92-7 (TES) - Body ground Always 10 kΩ or higher
K72-17 (E2) or K92-8 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C317591C85
1.51,0.333 1.927,0.583 0.417,0.25 0.771,0.979 0.656,0.583 true 0.854,1.604 0.792,1.24 true 0.49,0.396 0.948,0.594 0.458,0.198 10 false GND 0.719,1.646 1.198,1.844 0.479,0.198 10 false GND2 1.594,0.375 2.073,0.573 0.479,0.198 10 false K72 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-1 (GND) - Body ground Always Below 1 Ω
K72-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE, TES TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE, TES TERMINAL VOLTAGE)
a.

Reconnect the K72 multiplex tilt and telescopic ECU connector.


b.
C267905C70
1.417,0.24 1.979,0.51 0.563,0.271 1.948,1.552 1.583,1.135 true 1.24,1.531 1.302,1.146 true 2.427,1.563 1.719,1.146 true 1.542,0.292 1.927,0.5 0.385,0.208 10 false K72 1.156,1.552 1.438,1.719 0.281,0.167 10 false E2 1.844,1.563 2.167,1.792 0.323,0.229 10 false TES 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.302,1.563 2.76,1.76 0.458,0.198 10 false VCE
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Disconnect the K92 telescopic motor (steering column assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K72-14 (VCE) - K72-17 (E2) Engine switch on (IG) 8 to 14 V
K72-15 (TES) - K72-17 (E2) Engine switch on (IG) 8 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK TELESCOPIC POSITION SENSOR (STEERING COLUMN ASSEMBLY)

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TELESCOPIC POSITION SENSOR (STEERING COLUMN ASSEMBLY)
a.
C373326C04
1.531,0.063 1.938,0.26 0.406,0.198 0.938,1.865 1.594,1.344 true 0.604,1.323 1.385,1.26 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.594,0.083 1.906,0.281 0.313,0.198 10 false K92 0.344,1.25 0.656,1.448 0.313,0.198 10 false E2 0.594,1.844 0.906,2.042 0.313,0.198 10 false TES
*a Component with harness connected
(Telescopic Motor (Steering Column Assembly))


Reconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Reconnect the K92 telescopic motor (steering column assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K92-7 (TES) - K92-8 (E2) Steering column contracting or extending Pulse generation
High: 8 to 14 V
Low: Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.

Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.
C317591C86
1.51,0.333 1.927,0.583 0.417,0.25 0.958,0.969 0.844,0.573 true 0.708,0.396 1.167,0.594 0.458,0.198 10 false +B 1.604,0.375 2.083,0.573 0.479,0.198 10 false K72 0.094,0.083 0.552,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K72-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C317591C85
1.51,0.333 1.927,0.583 0.417,0.25 0.771,0.979 0.656,0.583 true 0.854,1.604 0.792,1.24 true 0.49,0.396 0.948,0.594 0.458,0.198 10 false GND 0.719,1.646 1.198,1.844 0.479,0.198 10 false GND2 1.594,0.375 2.073,0.573 0.479,0.198 10 false K72 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-1 (GND) - Body ground Always Below 1 Ω
K72-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR (STEERING COLUMN ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR (STEERING COLUMN ASSEMBLY))
a.

Disconnect the K72 multiplex tilt and telescopic ECU connector.


b.

Disconnect the K92 telescopic motor (steering column assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K72-6 (TEM+) - K92-4 (TEM+) Always Below 1 Ω
K72-19 (TEM-) - K92-1 (TEM-) Always Below 1 Ω
K72-6 (TEM+) or K92-4 (TEM+) - Body ground Always 10 kΩ or higher
K72-19 (TEM-) or K92-1 (TEM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TELESCOPIC MOTOR (STEERING COLUMN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TELESCOPIC MOTOR (STEERING COLUMN ASSEMBLY)
a.

Disconnect the K92 telescopic motor (steering column assembly) connector.


b.
C373325C04
1.51,0.208 1.896,0.438 0.385,0.229 1.365,1.208 0.75,0.875 true 2.021,1.198 2.625,0.885 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.323,0.76 0.781,1.042 0.458,0.281 10 false TEM+ 2.698,0.75 3.156,1.031 0.458,0.281 10 false TEM- 1.573,0.24 1.885,0.438 0.313,0.198 10 false K92
*a Component without harness connected
(Telescopic Motor (Steering Column Assembly))


Apply 12 V battery voltage to the telescopic motor (steering column assembly) connector. Then check the steering column telescopic operation.

OK:
Measurement Condition Specified Condition
·

12 V battery positive (+) lead → K92-4 (TEM+)

·

12 V battery negative (-) lead → K92-1 (TEM-)


The steering column contracts.
·

12 V battery positive (+) lead → K92-1 (TEM-)

·

12 V battery negative (-) lead → K92-4 (TEM+)


The steering column extends.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG