52171C
1.INSTALL REAR BUMPER REINFORCEMENT (for Type A)
Install the rear bumper reinforcement with the 6 bolts.
52171C
2.INSTALL REAR BUMPER REINFORCEMENT (for Type B)
Install the rear bumper reinforcement with the 6 bolts.
52615
3.INSTALL REAR BUMPER ENERGY ABSORBER (for Type A)
|
Install in this Direction |
Engage the 2 guides to install the rear bumper energy absorber as shown in the illustration.
52592
4.INSTALL REAR BUMPER SIDE SEAL LH
for Single Type:
Install the 3 clips.
for Dual Type:
Install the 2 clips.
Install the rear bumper side seal LH with 2 new grommets.
52591
5.INSTALL REAR BUMPER SIDE SEAL RH
Install the 2 clips.
Install the rear bumper side seal RH with 2 new grommets.
52563D
6.INSTALL REAR BUMPER UPPER RETAINER LH
Engage the grommet.
Engage the 2 guides to temporarily install the rear bumper upper retainer LH to the rear combination light assembly LH.
| *a | Pin |
| *b | Guide |
|
Install in this Direction |
Engage the guide and pin as shown in the illustration to temporarily install the rear bumper upper retainer LH and rear combination light assembly LH as a set.
Install the rear combination light assembly with the 2 screws.
Connect the connector.
Install the rear bumper upper retainer LH with the screw.
52562E
7.INSTALL REAR BUMPER UPPER RETAINER RH
Use the same procedure as for the LH side.
52576
8.INSTALL REAR BUMPER SIDE RETAINER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide as shown in the illustration.
Engage the 2 claws.
|
Install in this Direction |
Engage the 3 clips as shown in the illustration.
Install the rear bumper side retainer LH with the screw.
52575
9.INSTALL REAR BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
64722
10.INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER LH
64721
11.INSTALL LUGGAGE COMPARTMENT TRIM INNER COVER RH
58387
12.INSTALL REAR FLOOR FINISH PLATE
64749E
13.INSTALL LUGGAGE COMPARTMENT DOOR STRIKER COVER
64725D
14.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
64779E
15.INSTALL SPARE WHEEL COVER TRAY
64770
16.INSTALL SPARE WHEEL COVER ASSEMBLY
52461F
17.INSTALL REAR BUMPER PAD
When installing the rear bumper pad, heat the rear bumper cover using a heat light.
Use the same procedure for the RH side and LH side.
| Item | Temperature |
|---|---|
| Rear Bumper Cover | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper cover excessively.
Clean the rear bumper cover surface.
Using a heat light, heat the rear bumper cover surface.
Remove any remaining double-sided tape from the rear bumper cover.
Wipe off any tape adhesive residue with cleaner.
Remove the release paper from a new rear bumper pad.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Line |
Install the rear bumper pad as shown in the illustration.
Press the rear bumper pad firmly to install it.
52169C
18.INSTALL LOWER REAR BUMPER COVER (for Type A)
Engage the 12 claws.
Install the 2 clips.
Install the lower rear bumper cover with the 2 screws.
52166B
19.INSTALL REAR BUMPER CORNER EXTENSION LH (for Type B)
Engage the 4 guides and 4 claws to install the rear bumper corner extension LH.
52165D
20.INSTALL REAR BUMPER CORNER EXTENSION RH (for Type B)
Use the same procedure as for the LH side.
52724
21.INSTALL REAR BUMPER EXTENSION MOULDING LH (for Type B)
Engage the 4 claws to install the rear bumper extension moulding LH.
52723
22.INSTALL REAR BUMPER EXTENSION MOULDING RH (for Type B)
Use the same procedure as for the LH side.
81920
23.INSTALL REFLEX REFLECTOR ASSEMBLY LH
Engage the guide and claw.
Install the reflex reflector assembly LH with the screw.
81910
24.INSTALL REFLEX REFLECTOR ASSEMBLY RH
Use the same procedure as for the LH side.
25.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)
Clean the rear bumper cover.
Remove any remaining double-sided tape from the rear bumper cover.
Wipe off any tape adhesive residue with cleaner.
|
Primer |
Using a brush or felt, apply primer or equivalent to the ultrasonic sensor clip installation area.
Use a clean brush or felt.
Do not touch the rear bumper cover until the primer has dried.
Peel off the release paper from 2 new ultrasonic sensor clips.
Align the 2 ultrasonic sensor clips with the mark on the rear bumper cover and install it as shown in the illustration.
| *a | Line | - | - |
Ensure that the ultrasonic sensor clip is within the line.
The double-sided tape of an ultrasonic sensor clip will deteriorate if it is detached. Make sure to replace the ultrasonic sensor clip with a new one when reattachment is necessary.
Press the ultrasonic sensor clip with a force of 30 N (3.0 kgf) for 3 seconds to install the ultrasonic sensor clip firmly so that there is no clearance between the ultrasonic sensor clip and rear bumper cover.
82182
26.INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
Engage the 2 clamps to install the No. 2 luggage room wire.
89348R
27.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION
Use the same procedure for the RH side and LH side.
89342
28.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION
Use the same procedure for the RH side and LH side.