Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0327773 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 69760C 2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B469775C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inside locking cable assembly as shown in the illustration.


Hide 69720B 3.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B469776C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door lock remote control cable assembly as shown in the illustration.


Hide 69036A 4.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY

a.
B469777C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws as shown in the illustration.


b.
B469778

Engage the 2 claws to install the front door lock cover sub-assembly as shown in the illustration.


Hide 69040A 5.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.
B469769C01
2.979,2.906 2.813,2.552 false 2.948,2.917 3.26,3.115 0.313,0.198 10 false *1
*1 Front Door Lock Open Rod
V113147

Install in this Direction


Connect the front door lock open rod to the front door lock with motor assembly.

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Connect the connector.


Hide 6.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69220 7.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Hide 67404F 8.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68151C 9.INSTALL FRONT DOOR GLASS RUN

Hide 67856B 10.INSTALL FRONT DOOR PANEL PROTECTOR

Hide 68102 11.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 12.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 13.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Hide 67602 14.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 81230 15.INSTALL COURTESY LIGHT ASSEMBLY

Hide 74220 16.INSTALL FRONT ARMREST ASSEMBLY

Hide 17.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 18.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 74038A 19.INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Hide 67492A 20.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 22.INITIALIZE POWER WINDOW CONTROL SYSTEM