Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2017.09–2018.04
RM33A0E _56 Audio / Visual / Telematics _065374 NAVIGATION / MULTI INFO DISPLAY _0328126 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly and navigation ECU.

WIRING DIAGRAM

w/ Sliding Roof
E368001E01
0.688,3.125 2.094,3.625 1.406,0.5 10 false Telephone Microphone Assembly 2.885,3.135 4.021,3.563 1.135,0.427 10 false Roof Console Box Sub-assembly 5.583,4.271 6.01,4.49 0.427,0.219 10 false K1 5.75,5.583 6.938,6 1.188,0.417 10 false Radio and Display Receiver Assembly 2.979,5.563 3.406,5.781 0.427,0.219 10 false K17 2.979,5.729 4.042,5.979 1.063,0.25 10 false Navigation ECU 3.427,4.292 3.854,4.51 0.427,0.219 10 false MIC+ 2.75,0.792 3.177,1.01 0.427,0.219 10 false B 3.885,0.792 4.313,1.01 0.427,0.219 10 false V14 5.573,0.781 6,1 0.427,0.219 10 false K2 5.917,0.792 6.458,0.969 0.542,0.177 10 false MACC 5.917,1.26 6.344,1.479 0.427,0.219 10 false MIN+ 5.917,2.188 6.375,2.396 0.458,0.208 10 false SGND 5.927,2.698 6.354,2.917 0.427,0.219 10 false SNS2 3.354,1.25 3.844,1.458 0.49,0.208 10 false MCO+ 5.573,5.01 6,5.229 0.427,0.219 10 false 24 5.563,4.552 5.99,4.771 0.427,0.219 10 false 26 5.583,4.063 6.01,4.281 0.427,0.219 10 false 25 5.583,1.531 6.01,1.75 0.427,0.219 10 false 22 5.583,1.073 6.01,1.292 0.427,0.219 10 false 21 5.573,0.594 6,0.813 0.427,0.219 10 false 23 3.948,0.583 4.375,0.802 0.427,0.219 10 false 9 3.948,1.063 4.375,1.281 0.427,0.219 10 false 8 3.948,1.542 4.375,1.76 0.427,0.219 10 false 7 3.896,1.99 4.323,2.208 0.427,0.219 10 false 15 3.948,2.479 4.375,2.698 0.427,0.219 10 false 6 2.75,2.479 3.177,2.698 0.427,0.219 10 false 1 2.76,1.542 3.188,1.76 0.427,0.219 10 false 2 2.76,1.063 3.188,1.281 0.427,0.219 10 false 3 2.75,0.594 3.177,0.813 0.427,0.219 10 false 5 5.594,2.01 6.021,2.229 0.427,0.219 10 false 24 5.583,2.5 6.01,2.719 0.427,0.219 10 false 25 3.354,0.781 3.896,0.958 0.542,0.177 10 false MACC 3.396,1.729 3.885,1.938 0.49,0.208 10 false MCO- 5.927,1.74 6.354,1.958 0.427,0.219 10 false MIN- 3.458,2.188 3.917,2.396 0.458,0.208 10 false GND 3.396,2.698 3.823,2.917 0.427,0.219 10 false SNS2 5.917,4.271 6.406,4.479 0.49,0.208 10 false MCO+ 5.917,4.74 6.406,4.948 0.49,0.208 10 false MCO- 5.927,5.208 6.385,5.417 0.458,0.208 10 false SGND 3.458,4.76 3.885,4.979 0.427,0.219 10 false MIC- 3.833,4.177 4.26,4.396 0.427,0.219 10 false 13 3.844,4.646 4.271,4.865 0.427,0.219 10 false 14 2.76,1.271 3.188,1.49 0.427,0.219 10 false B 2.75,1.74 3.177,1.958 0.427,0.219 10 false B 2.76,2.698 3.188,2.917 0.427,0.219 10 false B 3.885,1.26 4.313,1.479 0.427,0.219 10 false V14 3.875,1.74 4.302,1.958 0.427,0.219 10 false V14 3.875,2.188 4.302,2.406 0.427,0.219 10 false V14 3.885,2.688 4.313,2.906 0.427,0.219 10 false V14 5.573,1.26 6,1.479 0.427,0.219 10 false K2 5.583,1.729 6.01,1.948 0.427,0.219 10 false K2 5.594,2.188 6.021,2.406 0.427,0.219 10 false K2 5.583,2.698 6.01,2.917 0.427,0.219 10 false K2 5.573,4.75 6,4.969 0.427,0.219 10 false K1 5.583,5.198 6.01,5.417 0.427,0.219 10 false K1 4.573,2.052 5.281,2.271 0.708,0.219 10 false (Shielded) 4.563,5.073 5.271,5.292 0.708,0.219 10 false (Shielded)

w/o Sliding Roof
E368003E04
0.688,3.125 2.073,3.583 1.385,0.458 10 false Telephone Microphone Assembly 2.906,3.125 4.031,3.573 1.125,0.448 10 false Roof Console Box Sub-assembly 2.729,0.802 3.229,1.083 0.5,0.281 10 false B 2.74,0.615 3.24,0.896 0.5,0.281 10 false 5 2.75,1.073 3.25,1.354 0.5,0.281 10 false 3 2.75,1.552 3.25,1.833 0.5,0.281 10 false 2 2.74,2.51 3.24,2.792 0.5,0.281 10 false 1 3.344,0.781 3.844,1.063 0.5,0.281 10 false MACC 3.354,1.24 3.854,1.521 0.5,0.281 10 false MCO+ 3.448,2.156 3.948,2.438 0.5,0.281 10 false GND 3.396,2.688 3.896,2.969 0.5,0.281 10 false SNS2 3.885,0.792 4.385,1.073 0.5,0.281 10 false V13 3.969,0.594 4.469,0.875 0.5,0.281 10 false 9 3.958,1.073 4.458,1.354 0.5,0.281 10 false 10 3.969,1.542 4.469,1.823 0.5,0.281 10 false 11 3.917,1.99 4.417,2.271 0.5,0.281 10 false 4 3.948,2.5 4.448,2.781 0.5,0.281 10 false 12 4.552,2.052 5.24,2.333 0.688,0.281 10 false (Shielded) 5.563,0.594 6.063,0.875 0.5,0.281 10 false 23 5.552,0.792 6.052,1.073 0.5,0.281 10 false K2 5.573,1.073 6.073,1.354 0.5,0.281 10 false 21 5.563,1.563 6.063,1.844 0.5,0.281 10 false 22 5.563,2 6.063,2.281 0.5,0.281 10 false 24 5.573,2.51 6.073,2.792 0.5,0.281 10 false 25 5.906,1.26 6.406,1.542 0.5,0.281 10 false MIN+ 5.74,5.604 6.938,6.052 1.198,0.448 10 false Radio and Display Receiver Assembly 2.75,1.281 3.25,1.563 0.5,0.281 10 false B 2.75,1.75 3.25,2.031 0.5,0.281 10 false B 2.74,2.698 3.24,2.979 0.5,0.281 10 false B 3.365,1.719 3.865,2 0.5,0.281 10 false MCO- 5.906,2.688 6.406,2.969 0.5,0.281 10 false SNS2 5.917,1.729 6.417,2.01 0.5,0.281 10 false MIN- 5.906,2.188 6.406,2.469 0.5,0.281 10 false SGND 5.917,0.792 6.417,1.073 0.5,0.281 10 false MACC 5.563,1.271 6.063,1.552 0.5,0.281 10 false K2 5.563,1.75 6.063,2.031 0.5,0.281 10 false K2 5.563,2.188 6.063,2.469 0.5,0.281 10 false K2 5.573,2.698 6.073,2.979 0.5,0.281 10 false K2 4.552,5.094 5.24,5.375 0.688,0.281 10 false (Shielded) 5.573,4.281 6.073,4.563 0.5,0.281 10 false K1 5.927,4.292 6.427,4.573 0.5,0.281 10 false MCO+ 5.583,4.75 6.083,5.031 0.5,0.281 10 false K1 5.573,5.208 6.073,5.49 0.5,0.281 10 false K1 5.917,4.76 6.417,5.042 0.5,0.281 10 false MCO- 5.927,5.208 6.427,5.49 0.5,0.281 10 false SGND 5.583,4.083 6.083,4.365 0.5,0.281 10 false 25 5.594,4.552 6.094,4.833 0.5,0.281 10 false 26 5.594,5.021 6.094,5.302 0.5,0.281 10 false 24 3.823,4.188 4.323,4.469 0.5,0.281 10 false 13 3.833,4.656 4.333,4.938 0.5,0.281 10 false 14 3,5.604 3.5,5.885 0.5,0.281 10 false K17 2.99,5.76 4.167,6 1.177,0.24 10 false Navigation ECU 3.438,4.323 3.938,4.604 0.5,0.281 10 false MIC+ 3.458,4.76 3.958,5.042 0.5,0.281 10 false MIC- 3.885,1.271 4.385,1.552 0.5,0.281 10 false V13 3.885,1.74 4.385,2.021 0.5,0.281 10 false V13 3.875,2.188 4.375,2.469 0.5,0.281 10 false V13 3.885,2.688 4.385,2.969 0.5,0.281 10 false V13

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
NG (w/ Sliding Roof) A
NG (w/o Sliding Roof) B
OK C



A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

C

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V14-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V14-8 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V14-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V14-8 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.
E360498C01
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 2.271,2.896 1.927,2.156 false 1.198,2.833 1.813,2.146 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360501C01
1.76,1.24 1.688,0.698 false 1.969,1.24 2.208,0.719 false 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.521,0.531 1.948,0.74 0.427,0.208 10 false MCO- 2.104,0.552 2.531,0.771 0.427,0.219 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

8.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371629C01
1.563,0.188 2.01,0.427 0.448,0.24 1.167,0.49 1.625,1.333 false 2.219,0.448 1.771,1.333 false 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 1.656,0.24 1.969,0.438 0.313,0.198 10 false V14 0.802,0.302 1.313,0.51 0.51,0.208 10 false MCO+ 2.281,0.313 2.792,0.521 0.51,0.208 10 false MCO- 2.823,3.438 3.333,3.646 0.51,0.208 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V14-8 (MCO+) - V14-7 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C05
1.427,2.792 1.885,3.052 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.677,1.573 1.417,0.865 false 1.833,1.552 2.094,0.854 false 2.448,2.448 2.708,1.75 false 1.031,0.74 1.542,1.01 0.51,0.271 10 false MCO+ 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.708 0.531,2.906 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.573,2.833 2.052,3.052 0.479,0.219 10 false B 2.167,0.75 2.708,0.969 0.542,0.219 10 false MCO- 2.135,2.396 2.677,2.615 0.542,0.219 10 false GND
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-8 (MCO+) - B-3 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-8 (MCO+) or B-3 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

8.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C06
1.427,2.938 1.885,3.198 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.969,1.583 2.229,0.885 false 2.5,2.281 2.708,1.75 false 1.813,1.583 1.375,0.917 false 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.896 0.531,3.094 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.583,2.979 2.063,3.198 0.479,0.219 10 false B 2.302,0.781 2.844,1 0.542,0.219 10 false SNS2 2.188,2.281 2.729,2.5 0.542,0.219 10 false GND 0.979,0.802 1.521,1.021 0.542,0.219 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-6 (SNS2) - B-1 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-6 (SNS2) or B-1 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V13 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V13-12 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V13-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V13-10 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V13-11 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V13-12 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V13-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V13-10 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V13-11 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.
E360498C03
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.188,2.885 1.927,2.146 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC. 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360499C01
1.74,1.698 1.573,1.385 false 1.219,1.719 1.458,1.385 false 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.031,1.719 1.479,1.958 0.448,0.24 10 false SNS2 1.667,1.698 2.156,1.958 0.49,0.26 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

14.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371634C03
1.448,0.177 1.906,0.458 0.458,0.281 2.063,2.135 1.792,1.448 false 1.198,2.146 1.542,1.427 false 0.156,0.167 0.552,0.375 0.396,0.208 10 false *a 1.542,0.24 1.938,0.448 0.396,0.208 10 false V13 0.823,2.104 1.323,2.302 0.5,0.198 10 false MCO- 2.115,2.083 2.615,2.281 0.5,0.198 10 false MCO+ 2.813,3.448 3.313,3.646 0.5,0.198 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 10 (MCO+) and 11 (MCO-) of the V13 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V13-10 (MCO+) - V13-11 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C11
1.5,2.75 1.917,3 0.417,0.25 1.417,0.583 1.833,0.833 0.417,0.25 1.042,1.531 0.771,0.969 false 1.51,2.083 1.625,1.74 false 2.156,2.208 1.917,1.771 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.198,2.073 1.708,2.354 0.51,0.281 10 false MCO- 2.208,2.177 2.719,2.458 0.51,0.281 10 false MCO+ 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.656,2.792 2.167,3.073 0.51,0.281 10 false B
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-10 (MCO+) - B-3 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-10 (MCO+) or B-3 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

14.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C12
1.458,2.75 1.885,3.01 0.427,0.26 1.417,0.563 1.844,0.823 0.427,0.26 1.042,1.531 0.771,0.969 false 1.417,2.073 1.531,1.729 false 1.854,2.125 1.646,1.75 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.052,2.083 1.563,2.365 0.51,0.281 10 false SNS2 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.604,2.792 2.115,3.073 0.51,0.281 10 false B 1.896,2.094 2.406,2.375 0.51,0.281 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-12 (SNS2) - B-1 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-12 (SNS2) or B-1 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the K1 radio and display receiver assembly connector.


b.

Disconnect the K17 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-25 (MCO+) - K17-13 (MIC+) Always Below 1 Ω
K1-26 (MCO-) - K17-14 (MIC-) Always Below 1 Ω
K1-25 (MCO+) or K17-13 (MIC+) - Body ground Always 10 kΩ or higher
K1-26 (MCO-) or K17-14 (MIC-) - Body ground Always 10 kΩ or higher
K1-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU)
a.

Disconnect the K17 navigation ECU connector.


b.

Turn the ignition switch to ACC.


c.
E368005C01
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 false 0.833,2.083 1.188,1.469 false 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.573,0.469 1.969,0.698 0.396,0.229 10 false K17 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU)


Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K17-13 (MIC+) - K17-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY