Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*)
·

Stop light switch assembly

·

SFI system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Connect the cable to the negative (-) battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the key indicator display is not displayed on the multi-information display). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the brake signal sent via direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the brake signal sent via direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2284
Power Source Control
·

Stop Light Switch1


Engine
·

Stop Light SW



WIRING DIAGRAM

B491203E01
4.979,3.375 5.99,3.646 1.01,0.271 10 false R8 4.979,3.531 6.5,3.948 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.177,5.104 5.75,5.385 0.573,0.281 10 false A37 5.177,5.26 6.281,5.635 1.104,0.375 10 false Stop Light Switch Assembly 3.375,6.354 4.49,6.677 1.115,0.323 10 false *1: for A25A-FKS 0.719,6.344 2.604,6.635 1.885,0.292 10 false : CAN Communication Line 0.896,3.365 1.469,3.646 0.573,0.281 10 false K27 0.802,1.615 2.302,1.906 1.5,0.292 10 false A24*1, A23*2, A22*3 0.813,1.781 1.385,2.063 0.573,0.281 10 false ECM 0.719,5.115 1.292,5.396 0.573,0.281 10 false A34 0.875,3.521 1.99,3.885 1.115,0.365 10 false Shift Lock Control Unit Assembly 0.708,5.292 2.24,5.677 1.531,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 2,4.542 2.573,4.823 0.573,0.281 10 false 42 2.01,2.792 2.583,3.073 0.573,0.281 10 false 4 2.01,0.979 3.156,1.208 1.146,0.229 10 false 21*1, 27*2, 9*3 1.615,1.094 2.188,1.375 0.573,0.281 10 false STP 5.021,0.979 5.594,1.26 0.573,0.281 10 false 25 5.073,4.573 5.646,4.854 0.573,0.281 10 false 3 5.917,1.156 6.49,1.438 0.573,0.281 10 false IC 5.271,4.573 5.844,4.854 0.573,0.281 10 false L 5.271,0.969 5.844,1.25 0.573,0.281 10 false STP1 5.688,4.677 6.26,4.958 0.573,0.281 10 false IC 1.604,2.927 2.177,3.208 0.573,0.281 10 false STP 1.615,4.677 2.188,4.958 0.573,0.281 10 false STP 4.667,6.354 5.885,6.635 1.219,0.281 10 false *2: for 2GR-FKS 5.896,6.344 7.115,6.625 1.219,0.281 10 false *3: for 2AR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A37 stop light switch assembly connector.


c.

Disconnect the A24*1, A23*2 or A22*3 ECM connector.


d.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the K27 shift lock control unit assembly connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-25 (STP1) - A37-3 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the R8 certification ECU (smart key ECU assembly) connector.


b.

Connect the A37 stop light switch assembly connector.


c.
B424431C19
1.49,0.177 1.906,0.427 0.417,0.25 1.083,2 1.333,2 1.333,2 1.344,1.167 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.604,0.219 1.917,0.417 0.313,0.198 10 false R8 0.698,1.906 1.26,2.156 0.563,0.25 10 false STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R8-25 (STP1) - Body ground Brake pedal released → depressed 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY