Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Smart Entry and Start System) › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328238 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Key Cannot be Registered  


DESCRIPTION

A maximum of 5 master key ID codes and 3 sub key ID codes can be registered.

WIRING DIAGRAM

E318141E19
5.615,0.75 6.073,0.948 0.458,0.198 10 false KSW 5.375,0.75 5.833,0.948 0.458,0.198 10 false 5 5.677,1.823 6.771,2.281 1.094,0.458 10 false Transponder Key ECU Assembly 5.667,1.677 6.125,1.875 0.458,0.198 10 false K60 2.667,1.24 3.125,1.438 0.458,0.198 10 false K31 2.677,1.396 5.104,1.708 2.427,0.313 10 false Unlock Warning Switch Assembly 2.833,0.771 3.292,0.969 0.458,0.198 10 false 2 4.365,0.76 4.823,0.958 0.458,0.198 10 false 1 6.271,0.365 6.729,0.563 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.CHECK REGISTRATION MODE
a.

Check that the system enters registration mode.

OK:

System enters registration mode.



Result:
Proceed to
OK
NG



OK

2.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION
a.

In registration mode, insert the door control transmitter assembly into the ignition key cylinder and check the security indicator light (telltale light assembly).

HINT:

If the new key ID code registration fails, code 2-1 will be output through the security light. Trying to re-register an already registered door control transmitter assembly will cause code 2-2 to be output when the door control transmitter assembly is inserted. If the number of registered key ID codes exceeds the maximum limit, code 2-3 will be output through the security indicator light (telltale light assembly). The output details are shown in the following illustration.


B111593C04
2.958,3.906 3.063,4.219 false 2.958,6 3.063,6.313 false 2.958,8.094 3.083,8.448 false 1.094,1.198 2.677,2.063 1.583,0.865 10 false *b 1.083,3.083 1.917,3.302 0.833,0.219 10 false *c 1.083,5.219 1.917,5.448 0.833,0.229 10 false *d 1.083,7.302 1.906,7.542 0.823,0.24 10 false *e 2.021,0.677 2.802,0.927 0.781,0.25 10 false 0.12 sec. 2.896,2.104 3.802,2.365 0.906,0.26 10 false 1.88 sec. 1.708,1.271 2,1.51 0.292,0.24 10 false On 1.677,1.708 2.115,1.927 0.438,0.219 10 false Off 1.74,3.177 2,3.438 0.26,0.26 10 false On 1.719,3.615 2.115,3.813 0.396,0.198 10 false Off 1.76,5.26 2.073,5.521 0.313,0.26 10 false On 1.729,5.698 2.115,5.938 0.385,0.24 10 false Off 2.01,2.531 2.781,2.76 0.771,0.229 10 false 0.25 sec. 2.208,4.052 3.01,4.281 0.802,0.229 10 false 0.25 sec. 2.854,4.24 3.573,4.469 0.719,0.229 10 false 0.5 sec. 3.438,2.729 4.063,2.948 0.625,0.219 10 false 1 sec. 1.771,7.365 2.083,7.594 0.313,0.229 10 false On 1.76,7.802 2.156,8.021 0.396,0.219 10 false Off 2.052,4.625 2.833,4.833 0.781,0.208 10 false 0.25 sec. 3.802,4.844 4.292,5.073 0.49,0.229 10 false 1 sec. 2.188,6.146 2.938,6.354 0.75,0.208 10 false 0.25 sec. 2.823,6.354 3.604,6.583 0.781,0.229 10 false 0.5 sec. 2.042,6.698 2.875,6.906 0.833,0.208 10 false 0.25 sec. 2.208,8.24 2.979,8.479 0.771,0.24 10 false 0.25 sec. 4.156,6.917 4.698,7.125 0.542,0.208 10 false 1 sec. 2.854,8.49 3.521,8.708 0.667,0.219 10 false 0.5 sec. 0.729,0.167 1.583,0.51 0.854,0.344 10 false *a
*a Security Indicator Light (Telltale Light Assembly) *b Normal (Immobiliser system is operating normally)
*c Code 2-1 *d Code 2-2
*e Code 2-3 - -



Result:
Result Proceed to
Code 2-1 or Code 2-3 is output A
Code 2-2 is output B



A

3.READ VALUE USING GTS (TRANSPONDER S-CODE, TRANSPONDER M-CODE)

B

END (REGISTERED DOOR CONTROL TRANSMITTER ASSEMBLY WAS USED)

3.READ VALUE USING GTS (TRANSPONDER S-CODE, TRANSPONDER M-CODE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Transponder S-code Number of registered sub key min. 0, max. 15 Number of registered sub keys displayed -
Transponder M-code Number of registered master key min. 0, max. 15 Number of registered master keys displayed -
Body Electrical > Immobiliser > Data List
Tester Display
Transponder S-code
Transponder M-code
50003 260 20,19

Result:
Result Proceed to
5 is displayed for "Transponder M-code" and 0 is displayed for "Transponder S-code" A
0 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" B
5 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" C
Values are other than above D



A

KEY REGISTRATION (SUB-KEY)

B

KEY REGISTRATION (MASTER KEY)

C

MAXIMUM NUMBER OF DOOR CONTROL TRANSMITTER ASSEMBLIES ALREADY REGISTERED

D

4.KEY REGISTRATION
4.KEY REGISTRATION
a.

Refer to the table below to determine if additional door control transmitter assemblies can be registered.

Number of Door control transmitter assemblies Registered (Master and Sub) Proceed to
0 New key ID code registration
1 to 7 Additional key ID code registration


b.

Check if an additional door control transmitter assembly can be registered.

OK:

Additional door control transmitter assembly can be registered.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL TRANSMITTER ASSEMBLY MALFUNCTION)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the K60 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K31-1 - K60-5 (KSW) Always Below 1 Ω
K31-2 - Body ground Always Below 1 Ω
K31-1 or K60-5 (KSW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR